Shear Pins
Browning® 1305002 Stock Shear Pin, 3/16 in Dia Neck, 1-1/8 in OD, For Use With Model SHH1 Hub, 3730 in-lb Torque, Steel
Browning® shear pin hubs are designed to shear a necked pin at a predetermined load. This protects equipment from overloads. Consisting of a hub assembly, a sprocket and shear pin, the shear pin bridges between the sprocket and hub assembly. The shear pin is available in load increments, so the closest one to your application requirements must be chosen. Resetting the shear pin hub is accomplished manually by replacing the shear pin. Best applied to applications where infrequent overloads are encountered.
Browning® 1305051 Stock Shear Pin, 7/32 in Dia Neck, 1-7/16 in OD, For Use With Model SHP1 Hub, 7330 in-lb Torque, Steel
Browning® shear pin hubs are designed to shear a necked pin at a predetermined load. This protects equipment from overloads. Consisting of a hub assembly, a sprocket and shear pin, the shear pin bridges between the sprocket and hub assembly. The shear pin is available in load increments, so the closest one to your application requirements must be chosen. Resetting the shear pin hub is accomplished manually by replacing the shear pin. Best applied to applications where infrequent overloads are encountered.
Browning® 1305168 Stock Shear Pin, 13/32 in Dia Neck, 2-7/16 in (SHQ1)/2-5/8 in (SHR1) OD, For Use With Model SHQ1/SHR1 Hub, 33530 in-lb Torque, Steel
Browning® shear pin hubs are designed to shear a necked pin at a predetermined load. This protects equipment from overloads. Consisting of a hub assembly, a sprocket and shear pin, the shear pin bridges between the sprocket and hub assembly. The shear pin is available in load increments, so the closest one to your application requirements must be chosen. Resetting the shear pin hub is accomplished manually by replacing the shear pin. Best applied to applications where infrequent overloads are encountered.
Martin Accu-Torch® SPP-29 Scratched Shear Pin, For Use With Bolt-On Shear Pin Sprocket, Steel
Shear pin sprockets provide simple, dependable protection against expensive machinery damage caused by overloads or jamming. Torque is transmitted by a single pin, necked to shear when the safe load is exceeded. When an overload occurs the pin shears, disconnecting the drive immediately. Shear pins can be necked to customer specific torque ratings.
Recently Viewed
Tsubaki® DS80A14 Type A Double Single Roller Chain Sprocket, 1 in Dia Bore, 4.98 in OD, 80 Chain, 14 Teeth, 1 in Pitch, Carbon Steel
This type of sprocket is commonly used in applications where two or more items are powered by a common drive shaft. The space between the sprocket plates is wider than a multi-strand sprocket and allows two separate strands of chain to engage without contacting each other. With this type of sprocket, one strand of chain may exit in a different direction than the other. For example, one strand exiting towards the ceiling and the other running parallel to the floor.
PTI 10B-31B Single Strand Hub Type B Roller Chain Sprocket, 20 mm Dia Bore, 163.9 mm OD, #10B-1 Chain, 31 Teeth, 15.875 mm Pitch, C45 Steel
Hub type metric sprockets are available with a minimum plain bore (pilot bore) and some stock finished bore sizes. Any shaft size is possible with our custom bore and keyway capability. Sprockets with hubs are typically fitted to the shaft as a clearance fit. They are held in place with two set screws and a keyway. Clearance fits are popular for light loads and slow speeds. A press fit (or shrink fit to the shaft) is usually preferred for higher speeds or heavier loads as they fit to the shaft more securely than a clearance fit sprocket. Depending on the clearance of the shaft fit, sprockets may work slightly on the shaft causing possible fretting or shaft wear. All sprockets are available with hardened teeth from stock or on request. Press fits usually require the sprocket to be heated for installation to expand the bore. As a heated sprocket cools, it shrinks, conforming to the shaft with a tight grip. A set screw can be used to secure the key. The TL taper bushed sprocket will function like the press fit sprocket and is generally easier to install.
Browning® 1112077 Double Single Strand Plate Type A Roller Chain Sprocket With Hardened Teeth, 5/8 to 1-7/8 in Dia Bore, 3.72 in OD, 50 Chain, 17 Teeth, 5/8 in Pitch, Steel
Browning® offers type A plate steel sprockets in single strands. Offerings include 25 to 200 pitch range.
