Browning 1-1/2"-ID QD F-STYLE BISHINGS BRW F-1-1/2
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
-
BrandBrowning®
-
UPC662289360017
-
Manufacturer Part Number1073725
-
CountryUSA
-
MaterialCast Iron
-
Flange Diameter6-5/8 in
-
Flange Thickness15/16 in
-
Torque Rating30000 in-lb
-
TypeType F
-
Screw Size9/16-12 x 3-5/8 in
-
Number of Bolt Holes3
-
Barrel Diameter4-3/8 in
-
Keyway Size3/8 x 3/16 in
-
Bolt Circle Diameter5-5/8 in
-
Bore Diameter1-1/2 in
-
Overall Length3.68 in
-
Suitable For Use WithGearbelt® Sheaves, Sprockets and Pulleys
- Reverse mounting ability - This bushing system allows for mounting on either side of the product to allow for a more flush view of the product face
- Taper on Barrel - Self locking taper provides the highest degree of mechanical locking product to product
- Wrapped FHP Belts are more tolerant to slipping and misalignment than Raw Edge Belts
- Reverse mounting ability - This bushing system allows for mounting on either side of the product to allow for a more flush view of the product face
- 3/4 in/ft Taper on Barrel - Self locking taper provides the highest degree of mechanical locking product to product
- Permit four-way mounting
- Easy installation and removal
-
UNSPSC31171516
-
Alternative Part NumberF 1 1/2
-
Package DescriptionEACH
-
Standards/ApprovalsABMA/AGMA/AIST/AWEA/CEMA/GEAPS/MPTA/NSSGA/PTDA Standards
-
Warranty1 Year
-
Warranty Information
-
Instruction/Installation Manual
Recently Viewed
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
ALE 10THHNYEL 10-THHN YELLOW STRANDED WIRE. THE THHN CONDUCTORS ARE PRIMARILY USED IN CONDUIT AS BRANCH CIRCUITS IN COMMERCIAL OR INDUSTRIAL APPLICATIONS.
TYPE THHN IS AVAILABLE STRANDED IN SIZES 14 AWG -750 KCMIT. THE CONDUCTORS ARE SOFT-ANNEALED, STRANDED OR SOLID COPPER AND ARE INSULATED WITH A TOUGH HEAT AND MOISTURE-RESISTANT POLYVINYL CHLORIDE, OVER WHICH A NYLON JACKSON IS APPLIED.
-ALE10THHNYEL >
ARC™ 12241 Premium Mounted Coated Abrasive Flap Wheel, 2 in Dia, 1 in W Face, 1/4-20 Dia Shank, 60 Grit, Coarse Grade, Aluminum Oxide Abrasive
Mounted and unmounted flap wheels are a great choice for light grinding, blending, deburring and finishing applications on a variety of metals. Flap wheels conform to many geometries and the radial flap design provides a continuous supply of fresh grain for consistent cutting action. Mounted flap wheels are most commonly used on die grinders.
EATON BR2020B100V 1-Phase Main Circuit Breaker Loadcenter, 120/240 V AC, 100 A, 20 Poles, 10 kA Interrupt
Specially designed for easy installation, Eaton's BR 1-inch load centers house the branch circuit breakers and the wiring required to distribute power to individual circuits. They serve as main breaker for service entrances or as main lug when adding circuits to existing service. The main breaker protects the entire panel and can be used as a service disconnect. The branch breakers protect the wires leading to individual electrical loads such as fixtures and outlets.
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
