1-GRV 1/2"-ID A OR B-BELT SHEAVES IDC BK-024-1/2
IDC Select® light duty bored-to-size sheaves are available in single and two groove designs for A-B and 3L-4L-5L belts. Each unit is supplied with a keyway and a set screw over the keyway. They are precision machined from 25 gray cast iron, statically balanced, painted with a baked enamel finish and individually packaged.
-
BrandIDC Select®
-
UPC887412012995
-
Manufacturer Part NumberIDC BK024-1/2
-
CountryUSA|Canada
-
Face Width13/16 in
-
Pitch Diameter2.2 in
-
FinishBaked Enamel
-
MaterialClass 25 Cast Iron
-
TypeLight Duty Type 1
-
Hub Projection13/32 in
-
Outside Diameter2.4 in
-
Bore Diameter1/2 in
-
Bore TypeBored to Size
-
Suitable For Use With4L/A and 5L/B Cross Section V-Belts
- Precision machined from gray cast iron
- Statically balanced
- Cast iron sheaves should not exceed 6500 fpm rim speed
- Special or dynamic balancing should be considered when speeds exceed 5000 fpm
- Without keyway
- 1.8 in Dia pitch 4L/2.2 in Dia pitch 5L(B)
-
UNSPSC31171804
-
Package Description1/PK
-
Standards/ApprovalsASTM Specified|SAE Standard
-
Technical Bulletin
-
Catalog
Recently Viewed
IDC Select® light duty bored-to-size sheaves are available in single and two groove designs for A-B and 3L-4L-5L belts. Each unit is supplied with a keyway and a set screw over the keyway. They are precision machined from 25 gray cast iron, statically balanced, painted with a baked enamel finish and individually packaged.
HCI Preferred Supplier 650488 Swivel Nut Connector, 3/4-16 Nominal, Male JIC Flare x Female JIC Flare, Steel
HCI Preferred Supplier 650488 Swivel Nut Connector, 3/4-16 Nominal, Male JIC Flare x Female JIC Flare, Steel
756328 DO-IT-BEST/RAID 17.5 OZ. OUTDOOR FRESH SCENT AEROSOL SPRAY WASP & HORNET KILLER
RAID WASP AND HORNET KILLER SPRAYS UP TO 22 FEET TO KILL WASPS, HORNETS, AND YELLOW JACKETS. KILLS THE ENTIRE NEST AND KILLS WITH RESIDUAL ACTION AS THEY RETURN TO THE NEST. KILLS WASPS AND HORNETS ON CONTACT AND IS ELECTRONICALLY NON-CONDUCTING UP TO 32,500 VOLTS. KILLS LARVAE AND PUPAE IN THE NEST
JWH756328 >
IDC Select® light duty bored-to-size sheaves are available in single and two groove designs for A-B and 3L-4L-5L belts. Each unit is supplied with a keyway and a set screw over the keyway. They are precision machined from 25 gray cast iron, statically balanced, painted with a baked enamel finish and individually packaged.
NIBCO 803-1/2 Apollo Press Small Diameter Lead Free Female Press Adapter, 1/2 in Nominal, C x FNPT End Style, Brass, Domestic
The APOLLOXPRESS® 803 Small Diameter Press Female Adapter features a Lead-Free dezincification resistant brass body and an EPDM O-Ring. Our Small Diameter APOLLOXPRESS® products are manufactured utilizing proven ASTM materials and standards. Proudly Made In The USA.
GARVIN® LL75 LL-Style Conduit Body With Unit Cover and Neoprene Gasket, 3/4 in Hub, Die Cast Aluminum, Powder Coated
3/4 in LL-style conduit bodies are attached to 3/4 in threaded rigid or IMC conduits when a change of direction is required. Their removable cover makes general maintece and wire pulling and feed through easy and convenient. Commonly used for electrical service entrance wires or as an economical convenience box when extra wire capacity is needed. Garvin Industries LL-style conduit bodies save time and money by eliminating costly bending of large conduits in order to change the directions of conduit runs. They allow the installer to easily bend wires into the smooth turns. Their powder coated finish and watertight gasket ensure a weatherproof installation. This item has a 2 hr fire rating.
