Gates® Power Transmission Super HC® Molded Notch PowerBand® 12/5VX1700 Heavy Duty Molded Notch V-Belt, 5VX Section, 5/8 in W Top, 170 in L Outside, 35/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
-
BrandGates® Power Transmission
-
UPC72053770728
-
Manufacturer Part Number12/5VX1700
-
CountryUSA|Canada
-
Temperature Range-60 to 250 deg F
-
Thickness35/64 in
-
MaterialEPDM
-
Top Width5/8 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeHeavy Duty Molded Notch
-
Minimum Pulley Diameter7.958 in
-
Section Size5VX
-
Series9389
-
Number of Ribs12
-
Outside Length170 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- Notches molded into the belt during manufacturing increase flexibility making this belt well suited for drives with smaller diameter sheaves
- The tie band assures high lateral rigidity, guiding the belt in a straight line and preventing it from coming off the drive
- Patented ethylene material construction provides -60 to 250 deg F temperature range to resist belt cracking
-
Alternative Part Number938912170
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Gates® Power Transmission Super HC® Molded Notch PowerBand® 12/5VX1700 Heavy Duty Molded Notch V-Belt, 5VX Section, 5/8 in W Top, 170 in L Outside, 35/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
United Abrasives-SAIT 57016 Close Coated General Purpose Abrasive Disc, 7 in Dia, 7/8 in Center Hole, 16 Grit, 2A Aluminum Oxide Abrasive
TUB & SINK HAIR STRAINER--CARDED-JWH407376 >
1/4" -MALE PIPE THREADX6" GALVANIZED NIPPLE-FIT1/4X6GN >
The forged steel jaws of this left-cutting snip are set at a 90-degree angle to the handles to allow easy gripping when cutting sheet metal in tight spaces or overhead. The operator can follow tight circular or square pattern left cuts with either a pushing or pulling motion. A serrated edge on the upper jaw and compound head-to-handle linkage provide powerful, non-slip leverage for cutting up to 24-gauge (0.61 mm) cold rolled steel or 28-gauge (0.38 mm) stainless. Handles feature non-slip, cushion inserts, torsion-spring action and a squeeze-open, side operated latch. Rust-resistant polished forged steel jaws and black oxide finished handle stampings promote long service life.
16-MJIC X 8-MORB 90-D HYD/ADAPTERS-DAY6801168>
