Gates® Power Transmission Super HC® Molded Notch PowerBand® 4/5VX1400 Heavy Duty Molded Notch V-Belt, 5VX Section, 5/8 in W Top, 140 in L Outside, 35/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
-
BrandGates® Power Transmission
-
UPC72053277890
-
Manufacturer Part Number4/5VX1400
-
CountryUSA|Canada
-
Temperature Range-60 to 250 deg F
-
Thickness35/64 in
-
MaterialEPDM
-
Top Width5/8 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeHeavy Duty Molded Notch
-
Minimum Pulley Diameter7.958 in
-
Section Size5VX
-
Series9389
-
Number of Ribs4
-
Outside Length140 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- Notches molded into the belt during manufacturing increase flexibility making this belt well suited for drives with smaller diameter sheaves
- The tie band assures high lateral rigidity, guiding the belt in a straight line and preventing it from coming off the drive
- Patented ethylene material construction provides -60 to 250 deg F temperature range to resist belt cracking
-
Alternative Part Number93894140
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Specification Sheet
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Gates® Power Transmission Super HC® Molded Notch PowerBand® 4/5VX1400 Heavy Duty Molded Notch V-Belt, 5VX Section, 5/8 in W Top, 140 in L Outside, 35/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
3/8" -HOSEX#6 FLAT FACE 90 LONG-MHDE0606FF90L >
JASON 3VX560 3VX Section Cogged Deep Wedge V-Belts (3/8-inch Top Width, 5/16-inch Thick)
JASON® 3VX560 Cogged Deep Wedge V-Belt, 3VX Section, 3/8 in W Top, 56 in L Outside, 7/8 in THK
Black Stallion® 97KCR-XL Driver Gloves, XL, Resists: Abrasion/Cut, ANSI Cut-Resistance Level: A6
Black Stallion 97KCR is a Grain cowhide palm with a split cowhide back. the 97KCR provides ANSI Cut Level A6 protection, isNFPA 70E compliant; It also offers ATPV=22 cal/cm2 (PPE Cat 2). Durable Para-Aramid stitching is used for spark and abrasion resistance. The keystone thumb and outside seam construction offers comfort and flexibility.
5" 600-GRIT PSA PAPER SANDING DISCS-SAI36811 >
Browning® 767376 VPLE 200 Normal Duty Pillow Block Ball Bearing, 1-1/4 in Dia Bore, 4-5/8 to 5-3/8 in L Bolt Center-to-Center, 1-13/16 in Base to Bore Centerline, 6-3/4 in OAL x 3-5/8 in OAH
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric, or BOA concentric locking collar. The contact seal, with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction. Depending on your preference, these bearings are available in inch and metric bore with a wide variety of cast iron, stamped steel or rubber mount housings or specific industry solutions as illustrated on the pages to follow.
