Gates® Power Transmission Super HC® Molded Notch PowerBand® 3/5VX1250 Heavy Duty Molded Notch V-Belt, 5VX Section, 5/8 in W Top, 125 in L Outside, 35/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
-
BrandGates® Power Transmission
-
UPC072053262520
-
Manufacturer Part Number3/5VX1250
-
CountryUSA|Canada
-
Temperature Range-60 to 250 deg F
-
Thickness35/64 in
-
MaterialEPDM
-
Top Width5/8 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeHeavy Duty Molded Notch
-
Minimum Pulley Diameter7.958 in
-
Section Size5VX
-
Series9389
-
Number of Ribs3
-
Outside Length125 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- Notches molded into the belt during manufacturing increase flexibility making this belt well suited for drives with smaller diameter sheaves
- The tie band assures high lateral rigidity, guiding the belt in a straight line and preventing it from coming off the drive
- Patented ethylene material construction provides -60 to 250 deg F temperature range to resist belt cracking
-
Alternative Part Number93893125
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Catalog
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission Super HC® Molded Notch PowerBand® 3/5VX1250 Heavy Duty Molded Notch V-Belt, 5VX Section, 5/8 in W Top, 125 in L Outside, 35/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
DOUBLE SHIELDED BALL BEARING WITH SNAP RING-NTN6206ZZNR >
GUIDE JOHN DEERE CORNHEAD-KABP151211>
Browning® 1251529 Straight Type LR Bevel Gear Reducer, Shaft Input, Shaft Output, 1 hp, 2:1 Gear, 875 rpm Maximum Output, 36.013 in-lb Input/57.62 in-lb Output Torque Rating
Browning® cast iron bevel and spiral bevel gear reducers are constructed of rugged cast iron housings. These housings are line bored for precise gear and bearing alignment. To offer maximum performance, these reducers are designed with tapered roller and ball bearings. Browning® cast iron bevel and spiral bevel gear reducers are available in six sizes and ratios. These range from 1:1 to 3:1, with speed-up ratios available. Torque capacity ranges from 99 to 5942 in-lb.
3/4" -MALE PIPE THREADX4" STAINLESS STEEL NIPPLE-FIT3/4X4SSN >
S-290 SUPER GLUE--CARDED-JWH354388 >
