Gates® Power Transmission Micro-V® 580J6 Heavy Duty V-Belt, J Section, 3/32 in W Top, 58 in L Outside, 5/32 in THK, Chloroprene
Exclusive truncated (shortened) profile gives Gates® Micro-V® belts increased flexibility, reduced heat buildup and allows performance at higher speeds on smaller diameter sheaves.
-
BrandGates® Power Transmission
-
UPC072053294361
-
Manufacturer Part Number580J6
-
CountryUSA
-
Thickness5/32 in
-
MaterialChloroprene
-
Top Width3/32 in
-
Reinforced MaterialPolyester
-
TypeHeavy Duty
-
Minimum Pulley Diameter3.183 in
-
Section SizeJ
-
Series9171
-
Number of Ribs6
-
Outside Length58 in
- Fiber reinforced ribs for excellent wear resistance
- High modulus, low stretch tensile member for added strength and dependability
- Smooth running for minimal vibration at high speeds
- Oil and heat-resistant, static conductivity
-
Alternative Part Number917105806
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Specification Sheet
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission Micro-V® 580J6 Heavy Duty V-Belt, J Section, 3/32 in W Top, 58 in L Outside, 5/32 in THK, Chloroprene
Exclusive truncated (shortened) profile gives Gates® Micro-V® belts increased flexibility, reduced heat buildup and allows performance at higher speeds on smaller diameter sheaves.
The steel Drop-in™ is an all steel, machine bolt anchor available in carbon steel and two types of stainless steel. It can be used in solid concrete, hard stone and solid block base materials. A coil thread version for forming applications is also available.
30-GPH FOUNTAIN PUMP-JWH755474>
Gates® Power Transmission Micro-V® 260J6 Heavy Duty V-Belt, J Section, 3/32 in W Top, 26 in L Outside, 5/32 in THK, Chloroprene
Exclusive truncated (shortened) profile gives Gates® Micro-V® belts increased flexibility, reduced heat buildup and allows performance at higher speeds on smaller diameter sheaves.
Sealmaster® 703378 SEHB Non-Expansion Standard-Duty Hanger Ball Bearing Unit, 1 in Dia Bore, 3-1/8 in OD, 1-1/2 in W, Cast Iron Bearing, Set Screw Collar Locking
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
Dichtomatik 75102179 O-Ring, 257 Dash Number, 5.859 in ID x 6.137 in OD, FKM, 75 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
