Gates® Power Transmission Micro-V® 180J6 Heavy Duty V-Belt, J Section, 3/32 in W Top, 18 in L Outside, 5/32 in THK, Chloroprene
Exclusive truncated (shortened) profile gives Gates® Micro-V® belts increased flexibility, reduced heat buildup and allows performance at higher speeds on smaller diameter sheaves.
-
BrandGates® Power Transmission
-
UPC072053237634
-
Manufacturer Part Number180J6
-
CountryUSA
-
Thickness5/32 in
-
MaterialChloroprene
-
Top Width3/32 in
-
Reinforced MaterialPolyester
-
TypeHeavy Duty
-
Minimum Pulley Diameter3.183 in
-
Section SizeJ
-
Series9171
-
Number of Ribs6
-
Outside Length18 in
- Fiber reinforced ribs for excellent wear resistance
- High modulus, low stretch tensile member for added strength and dependability
- Smooth running for minimal vibration at high speeds
- Oil and heat-resistant, static conductivity
-
Alternative Part Number917101806
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Catalog
-
Instruction/Installation Manual
-
Specification Sheet
Recently Viewed
Gates® Power Transmission Micro-V® 180J6 Heavy Duty V-Belt, J Section, 3/32 in W Top, 18 in L Outside, 5/32 in THK, Chloroprene
Exclusive truncated (shortened) profile gives Gates® Micro-V® belts increased flexibility, reduced heat buildup and allows performance at higher speeds on smaller diameter sheaves.
Dodge® Tigear-2® 23Q40R14 Standard Right Angle Worm Gear Speed Reducer, Quill Input, Solid B Shaft Output, 1.11 hp, 40:1 Gear, 44 rpm Maximum Output, 1193 in-lb Torque Rating
The speed reducer shall be a single reduction worm gear reducer incorporating three input configurations - a quill style for direct attachment of electric motors, a separate keyed input shaft suitable for flexible coupling to a footed motor or belt and pulley input configuration and a motor adapter style input that employs a three piece coupling to connect electric motors to the reducer. These input configurations shall be available in both solid and hollow output shaft designs. The reducer shall be manufactured in the United States of America.
Gates® Power Transmission Micro-V® 220J6 Heavy Duty V-Belt, J Section, 3/32 in W Top, 22 in L Outside, 5/32 in THK, Chloroprene
Exclusive truncated (shortened) profile gives Gates® Micro-V® belts increased flexibility, reduced heat buildup and allows performance at higher speeds on smaller diameter sheaves.
Dodge® Tigear-2® 20Q10R56 Standard Right Angle Worm Gear Speed Reducer, Quill Input, Solid B Shaft Output, 2.25 hp, 10:1 Gear, 175 rpm Maximum Output, 725 in-lb Torque Rating
The speed reducer shall be a single reduction worm gear reducer incorporating three input configurations - a quill style for direct attachment of electric motors, a separate keyed input shaft suitable for flexible coupling to a footed motor or belt and pulley input configuration and a motor adapter style input that employs a three piece coupling to connect electric motors to the reducer. These input configurations shall be available in both solid and hollow output shaft designs. The reducer shall be manufactured in the United States of America.
Dodge® Tigear-2® 23A15HA14 Standard Right Angle Worm Gear Speed Reducer, 3-Piece Coupled Input, Hollow Shaft Output, 3.30 hp, 15:1 Gear, 117 rpm Maximum Output, 1199 in-lb Torque Rating
The Tigear-2® is a right angle, single stage worm gear reducer with a rugged cast iron housing and power dense gearing design to ensure maximum reliability. Stainless Steel and the exclusive E-Z-Kleen® finish are available for tough washdown applications.
Dodge® Tigear-2® 20Q25L56 Standard Right Angle Worm Gear Speed Reducer, Quill Input, Solid A Shaft Output, 1.11 hp, 25:1 Gear, 70 rpm Maximum Output, 788 in-lb Torque Rating
The speed reducer shall be a single reduction worm gear reducer incorporating three input configurations - a quill style for direct attachment of electric motors, a separate keyed input shaft suitable for flexible coupling to a footed motor or belt and pulley input configuration and a motor adapter style input that employs a three piece coupling to connect electric motors to the reducer. These input configurations shall be available in both solid and hollow output shaft designs. The reducer shall be manufactured in the United States of America.
