Gates® Power Transmission Micro-V® 180J10 Heavy Duty V-Belt, J Section, 3/32 in W Top, 18 in L Outside, 5/32 in THK, Chloroprene
Exclusive truncated (shortened) profile gives Gates® Micro-V® belts increased flexibility, reduced heat buildup and allows performance at higher speeds on smaller diameter sheaves.
-
BrandGates® Power Transmission
-
UPC072053511284
-
Manufacturer Part Number180J10
-
CountryUSA
-
Thickness5/32 in
-
MaterialChloroprene
-
Top Width3/32 in
-
Reinforced MaterialPolyester
-
TypeHeavy Duty
-
Minimum Pulley Diameter3.183 in
-
Section SizeJ
-
Series9171
-
Number of Ribs10
-
Outside Length18 in
- Fiber reinforced ribs for excellent wear resistance
- High modulus, low stretch tensile member for added strength and dependability
- Smooth running for minimal vibration at high speeds
- Oil and heat-resistant, static conductivity
-
Alternative Part Number917101810
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission Micro-V® 180J10 Heavy Duty V-Belt, J Section, 3/32 in W Top, 18 in L Outside, 5/32 in THK, Chloroprene
Exclusive truncated (shortened) profile gives Gates® Micro-V® belts increased flexibility, reduced heat buildup and allows performance at higher speeds on smaller diameter sheaves.
Gates® Power Transmission Micro-V® 220J10 Heavy Duty V-Belt, J Section, 3/32 in W Top, 22 in L Outside, 5/32 in THK, Chloroprene
Exclusive truncated (shortened) profile gives Gates® Micro-V® belts increased flexibility, reduced heat buildup and allows performance at higher speeds on smaller diameter sheaves.
Gates® Power Transmission Nu-T-Link® NTL/B V-Belt, B Section, 21/32 in W Top, 50 ft L Outside, Polyurethane-Polyester Composite
Designed for rapid installation in an assortment of lengths and operating conditions.
Browning® 1251016 Type LR Spiral Bevel Gear Reducer, Shaft Input, Shaft Output, 1 hp, 1:1 Gear, 1750 rpm Maximum Output, 36.013 in-lb Input/28.81 in-lb Output Torque Rating
Browning® cast iron bevel and spiral bevel gear reducers are constructed of rugged cast iron housings. These housings are line bored for precise gear and bearing alignment. To offer maximum performance, these reducers are designed with tapered roller and ball bearings. Browning® cast iron bevel and spiral bevel gear reducers are available in six sizes and ratios. These range from 1:1 to 3:1, with speed-up ratios available. Torque capacity ranges from 99 to 5942 in-lb.
Morse® Raider® Plus XA0038 Single Reduction Standard Worm Gear Reducer, C-Face Quilled Input, Double Solid Shaft Output, 0.33 hp, 10:1 Gear Ratio, 175 rpm Maximum Output, 117 in-lb Output Torque Rating
Raider® Plus worm gear reducers represent the most flexible worm gear product in the power transmission solutions portfolio. With a large variety of add-on accessories, the Raider® Plus line of worm gear reducers is a problem solver. Four unit styles form the basis of this vast product offering. These are the universal style (U style, shaft input) with an output shaft and the C-face style (Q style, input quill) with an output shaft. Both the U and Q styles are also available with hollow outputs. The Raider® Plus worm gear reducer is designed as an industry interchange. It is dimensionally interchangeable with the major industry competitors.
Gates® Power Transmission Nu-T-Link® NTL/C V-Belt, C Section, 7/8 in W Top, 50 ft L Outside, Polyurethane-Polyester Composite
Designed for rapid installation in an assortment of lengths and operating conditions.
