Gates AX53 Tri-Power® Industrial V-Belts - AX Section, 1/2 in Top Width, 1 Strand, 55.0000 in Nominal Outside Length, Cogged
Most traditional v-belts struggle with small spaces and cause frequent interruptions, leading to costly downtime. Reduce these common drive issues with Tri-Power, your tried-and-true classical section replacement V-belt. The Tri-Power bandless V-belt is specifically designed to tackle the challenges associated with small sheave diameters on existing drives. Whether powering compressors, pumps, or other critical equipment, this belt ensures that your machinery runs efficiently and reliably. The advantage of this bandless V-belt lies in its ability to provide a like-for-like replacement without the need for full-system replacements. Its advanced design not only suits small sheaves but also enhances power transmission and reduces maintenance needs. Choose Gates Tri-Power V-belts for a dependable high-quality solution that keeps your existing drives running longer without interruptions.
-
BrandGates® Power Transmission
-
UPC72053200416
-
Manufacturer Part NumberAX53
-
CountryUSA|Canada
-
Temperature Range-60 to 250 deg F
-
Thickness5/16 in
-
MaterialEPDM
-
Top Width1/2 in
-
Reinforced MaterialPolyester
-
ColorBlack
-
TypeHeavy Duty
-
Section SizeAX
-
Series9012
-
Number of Ribs1
-
Outside Length55 in
- Notches molded into the belt during manufacturing make this belt well suited for drives with smaller diameter sheaves
- Belt edge is machined for even sheave groove contact resulting in less slip and wear
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- Patented EPDM Material construction provides -60 to 250 deg F temperature range to resist belt cracking
- Suitable for all industrial applications, particularly where small or sub-minimal sheave diameters are required
- Meets RMA oil and heat resistant standards
- Meets RMA static conductivity requirements
- Multi-duty recommended sheaves
- ARPM number: AX53
| Competitor Name | Cross-Reference Number |
|---|---|
| Motion Industries | 00719423 |
-
UNSPSC26101400
-
Standards/ApprovalsRMA Standard
-
Alternative Part Number90122053
-
Package DescriptionEACH
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Gates AX53 Tri-Power® Industrial V-Belts - AX Section, 1/2 in Top Width, 1 Strand, 55.0000 in Nominal Outside Length, Cogged
Most traditional v-belts struggle with small spaces and cause frequent interruptions, leading to costly downtime. Reduce these common drive issues with Tri-Power, your tried-and-true classical section replacement V-belt. The Tri-Power bandless V-belt is specifically designed to tackle the challenges associated with small sheave diameters on existing drives. Whether powering compressors, pumps, or other critical equipment, this belt ensures that your machinery runs efficiently and reliably. The advantage of this bandless V-belt lies in its ability to provide a like-for-like replacement without the need for full-system replacements. Its advanced design not only suits small sheaves but also enhances power transmission and reduces maintenance needs. Choose Gates Tri-Power V-belts for a dependable high-quality solution that keeps your existing drives running longer without interruptions.
BBI 489024 Fully Threaded Carriage Bolt, 1/4-20, 2 in L Under Head, Low Carbon Steel, A Grade, Zinc CR+3
BBI 489024 Fully Threaded Carriage Bolt, 1/4-20, 2 in L Under Head, Low Carbon Steel, A Grade, Zinc CR+3
Rust-Oleum High Performance 2300 System Inverted Striping Spray Paint creates bright, sharp and long-lasting lines for a variety of surfaces. This oil-based paint is ideal for parking lots, warehouse aisles, pallet positions, stadiums and more.
6-GRV 5-V-BELT QUICK DISCONNECT SD-BUSH SHEAVES-IDC6/5V0520SD >
General Pipe Cleaners 50BH Flat Sewer Rod With Holder, 1/2 x 1/16 in, For Use With 2 to 3 in Medium Pipe, Steel
Made from non-kinkable, high carbon, oil tempered steel. The Flat Sewer Rod is equipped with aluminum grip handle and steel spear head. With a comfortable, efficient Quick- Grip Handle that makes the work go faster.
MORSE® 90786 5943T Center Cutting Regular Length Single End End Mill, 7/32 in Dia Cutter, 5/8 in Length of Cut, 4 Flutes, 1/4 in Dia Shank, 2-1/2 in OAL, TiAlN Coated
