Gates® Power Transmission Hi-Power® II E240 Banded Heavy Duty V-Belt, E Section, 1-1/2 in W Top, 244 in L Outside, 29/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC72053211733
-
Manufacturer Part NumberE240
-
CountryUSA|Canada
-
Thickness29/32 in
-
MaterialEPDM
-
Top Width1-1/2 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter11.141 in
-
Section SizeE
-
Series9006
-
Number of Ribs1
-
Outside Length244 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
- Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather and aging
-
Alternative Part Number90062240
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Specification Sheet
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Gates® Power Transmission Hi-Power® II E240 Banded Heavy Duty V-Belt, E Section, 1-1/2 in W Top, 244 in L Outside, 29/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
FLAME RESIST HARNESS STRAP COVER-FRE400SCFR >
Mueller® 160-808 Repair Clamp, 2 in Pipe/Tube, Steel, Galvanized
MORSE® 57471 5929 Center Cutting Regular Length Single End End Mill, 1/2 in Dia Cutter, 1 in Length of Cut, 4 Flutes, 1/2 in Dia Shank, 3 in OAL, Bright
MORSE® 57929 5943 Center Cutting Regular Length Single End Mill, 29/64 in Dia Cutter, 1 in Length of Cut, 4 Flutes, 1/2 in Dia Shank, 3 in OAL, Bright
Milwaukee® HOLE DOZER™ 49-56-0724 Hole Saw With Carbide Teeth, 2-1/4 in Dia, 1.62 in D Cutting, Carbide Cutting Edge, 5/8-18 Arbor
The MILWAUKEE® 2-1/4" HOLE DOZER™ with Carbide Teeth Hole Saw features a new 3 TPI design that offers fast cuts with the durability of a bi-metal hole saw and life of a carbide hole saw. This Milwaukee hole saw provides the longest life in general purpose and extreme materials with the ability to cut through stainless steel, cast iron, fastener embedded wood, cement board, fiberglass, plaster, asphalt shingles, and more with ease. Deep gullets clear material fast while cutting, and Milwaukee's ALL-ACCESS SLOTS solve the frustration of plug removal for more productivity with less downtime between holes. The new slot design also provides increased pilot visibility for accurate placement and faster chip ejection keeping cuts cool. The HOLE DOZER™ with Carbide Teeth Hole Saw has a cutting depth of 1.62 in., allowing clearance to handle cuts in a wide range of materials. Milwaukee HOLE DOZER™ with Carbide Teeth Hole Saws are proudly made in the USA.
