Gates® Power Transmission Hi-Power® II C92 Banded Heavy Duty V-Belt, C Section, 7/8 in W Top, 96 in L Outside, 17/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC072053310290
-
Manufacturer Part NumberC92
-
CountryUSA|Canada
-
Thickness17/32 in
-
MaterialEPDM
-
Top Width7/8 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter7.958 in
-
Section SizeC
-
Series9004
-
Number of Ribs1
-
Outside Length96 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
- Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather and aging
| Competitor Name | Competitor Part Number |
|---|---|
| Motion Industries | 00679491 |
-
Alternative Part Number90042092
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Catalog
-
Instruction/Installation Manual
-
Specification Sheet
Recently Viewed
Gates® Power Transmission Hi-Power® II C92 Banded Heavy Duty V-Belt, C Section, 7/8 in W Top, 96 in L Outside, 17/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
Dodge® 023093 103 Non-Expansion Type E-Xtra Triple Lip Flange Mount Roller Bearing Unit, 1-3/16 in Dia Bore, 2.88 in L Bolt Center-to-Center, 4-Bolt Base Flange Mount, 3-3/4 in OAL/Dia
Dodge® 023093 103 Non-Expansion Type E-Xtra Triple Lip Flange Mount Roller Bearing Unit, 1-3/16 in Dia Bore, 2.88 in L Bolt Center-to-Center, 4-Bolt Base Flange Mount, 3-3/4 in OAL/Dia
SHOP-VACUUM CLEANER DISC FILTER-JWH344117 >
40-MM-ID PILLOW BLOCK UNIT-IDCUCP20840MM >
Entire clip is galvanized to resist corrosive and rusting action
Achieves 80% efficiency of published wire rope breaking strength
Bolts are an integral part of the saddle
Saddle is made from forged steel
Nuts can be installed in such a way as to enable the operator to swing the wrench in a full arc for fast installation
Assembled with standard heavy hex nuts
Satisfies ASME B30.26 requirements
Koyo CRS-10-1 Inch Series Stud Type Uncaged Needle Bearing Track Roller, 5/8 in Dia x 0.438 in W Roller, 1/4 in Dia x 3/4 in L Stud, Steel Roller
Track rollers (also known as cam followers) are characterized by their thick-walled outer rings that run directly on a track. The thick outer rings permit high load-carrying capability while minimizing both distortion and bending stresses. Sealed designs with internal thrust washers help extend service life under conditions of infrequent lubrication.
