Gates® Power Transmission Hi-Power® II PowerBand® 3/C68 Banded Heavy Duty V-Belt, C Section, 7/8 in W Top, 72 in L Outside, 17/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC72053259728
-
Manufacturer Part Number3/C68
-
CountryUSA|Canada
-
Thickness17/32 in
-
MaterialEPDM
-
Top Width7/8 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter7.958 in
-
Section SizeC
-
Series9094
-
Number of Ribs3
-
Outside Length72 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The tie band assures high lateral rigidity, guiding the belt in a straight line and preventing it from coming off the drive
- Concave sidewalls provide proper cord support and full contact with the sheave groove for equal loading and uniform wear
-
Alternative Part Number90943068
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Specification Sheet
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission Hi-Power® II PowerBand® 3/C68 Banded Heavy Duty V-Belt, C Section, 7/8 in W Top, 72 in L Outside, 17/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
The Power-Stud® anchor, is a fully threaded, torque-controlled, wedge expansion anchor. It is available in a threaded version suitable for applications in solid concrete and grout-filled concrete masonry. The threaded version is produced in type 304 and type 316 stainless steel.
United Abrasives-SAIT 23207 Thin High Speed Cut-Off Wheel, 6 in Dia x 0.035 in THK, 1/2 in Center Hole, A60T Grit, Aluminum Oxide Abrasive
!e9s2fchbzbr1nzoug+g--60_57_100x100.jpg)
1-1/4" FLARE NOZZLE-PDTLV5551807 >
Gates® Power Transmission MegaCrimp™ 6G-6FJX90M G25 Medium Bent Tube Hydraulic Coupling, 3/8 in x 9/16-18 Nominal, Hose x 37 deg Female JIC Flare Swivel, Steel
It’s what’s inside the MegaCrimp coupling that makes it perform so well, the “C” insert. This “C” insert allows usage with different hose constructions and wall thicknesses. In addition, the C-insert ensures an even distribution of crimping forces to form a concentric seal. That simplifies your inventory requirements since one size can accommodate many different hose ODs, on both one- and two-wire braid hoses and select Xpiral hoses. An additional bonus: MegaCrimp couplings are fully qualified for SAE, EN, and ISO performance.
Smith Bearing® CR-7/8-XB Cylindrical Stud Type Needle Bearing Cam Follower, 7/8 in Dia x 1/2 in W Roller, 3/8 in Dia x 7/8 in L Stud, 52100 Steel Roller
Hex head stud type needle roller bearings are recommended where running loads and shock loads are moderate. Bearing capacity of the stud type series is limited by the moderately sized stud. Manufactured from high alloy bearing quality steel.
