Gates® Power Transmission Hi-Power® II PowerBand® 12/B105 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 108 in L Outside, 13/32 in THK, EPDM
The PowerBand® construction allows multiple belts to function as a single unit, with even load distribution and each strand fitting securely in the sheave groove.
-
BrandGates® Power Transmission
-
UPC072053475845
-
Manufacturer Part Number12/B105
-
CountryUSA
-
Thickness13/32 in
-
MaterialEPDM
-
Top Width21/32 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter5.73 in
-
Section SizeB
-
Series9093
-
Number of Ribs12
-
Outside Length108 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The tie band assures high lateral rigidity, guiding the belt in a straight line and preventing it from coming off the drive
- Concave sidewalls provide proper cord support and full contact with the sheave groove for equal loading and uniform wear
-
Alternative Part Number909312105
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission Hi-Power® II PowerBand® 12/B105 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 108 in L Outside, 13/32 in THK, EPDM
The PowerBand® construction allows multiple belts to function as a single unit, with even load distribution and each strand fitting securely in the sheave groove.
WaterWeld™ will plug or seal leaks and patch holes and cracks in almost anything. Ideal for repairing plumbing, fuel tanks, tub and shower, drains, pool and spa, boats and potable water tanks, setup occurs even under water. After curing, it can be drilled, tapped, filed, sanded and painted. WaterWeld™ has a set time of 15 to 25 min and sets hard in one hour. WaterWeld™ cures to an off white color, is rated at a tensile strength of 900 psi and will withstand temperatures up to 300 deg F.
Smith Bearing® CR-3/4-XBE Cylindrical Stud Type Needle Bearing Cam Follower With Eccentric Bushing, 3/4 in Dia x 1/2 in W Roller, 1/2 in Dia x 7/8 in L Stud, 52100 Steel Roller
A press fit eccentric sleeve provides correct alignment and adjustment without costly preparation of close tolerance mounting holes and members. Eliminate problems of clearances, preloading and wear compensation and assure load sharing in multiple cam follower applications. Offer two model are non-crowned outer race and crowned outer race.
Appleton® ETP™ 7250S 7000S Non-Insulated Throat Straight Compression Connector, 2-1/2 in Trade, For Use With EMT Conduit, Steel, Zinc Electroplated
Appleton® offer ETP™ 7000S Series steel EMT compression connectors. They are used to ground and secure EMT raceways to boxes and enclosures. The 7000S Series have a male NPS threaded hub and are available with or without an insulated throat.
Smith Bearing® CR-2-1/2-X Cylindrical Stud Type Needle Bearing Cam Follower, 2-1/2 in Dia x 1-1/2 in W Roller, 1 in Dia x 2-1/4 in L Stud, 52100 Steel Roller
Screwdriver slot stud type needle roller bearings are recommended where running loads and shock loads are moderate. Bearing capacity of the stud type series is limited by the moderately sized stud. Manufactured from high alloy bearing quality steel. Most commonly used general purpose cam follower and available in sealed versions.
Smith Bearing® SMITH XTREME™ NUKR-35 Crowned Double Row Heavy Duty Roller Stud Type Needle Bearing Cam Follower, 35 mm Dia x 18 mm W Roller, 16 mm Dia x 32.5 mm L Stud, 52100 Steel Roller
Made with a double row of heavy rollers for extremely high load applications. These heavy duty bearings are assembled with metallic side shields helping to retain grease and keep out containments.
