Gates® Power Transmission Hi-Power® II B77 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 80 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC072053207378
-
Manufacturer Part NumberB77
-
CountryUSA|Canada
-
Thickness13/32 in
-
MaterialEPDM
-
Top Width21/32 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter4.775 in
-
Section SizeB
-
Series9003
-
Number of Ribs1
-
Outside Length80 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
- Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather and aging
| Competitor Name | Competitor Part Number |
|---|---|
| Motion Industries | 00678599 |
-
Alternative Part Number90032077
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Catalog
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission Hi-Power® II B77 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 80 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
FYH® UCP206 30MM UCP Normal Duty Pillow Block Unit, 30 mm Dia Bore, 4-3/4 in L Bolt Center-to-Center, 1-11/16 in Base to Bore Centerline, 6-1/2 in OAL 3-1/16 in OAH
FYH® UCP206 30MM UCP Normal Duty Pillow Block Unit, 30 mm Dia Bore, 4-3/4 in L Bolt Center-to-Center, 1-11/16 in Base to Bore Centerline, 6-1/2 in OAL 3-1/16 in OAH
Deep Groove Ball Bearings (DGBB) are the most common form of rolling bearings and are used in a variety of applications, particularly those where high speeds and low power loss are required. NSK DGBB can handle not only radial forces, but also moderate axial loads in both directions. They are easy to install and can be deployed in a variety of configurations.
Gates® Power Transmission Hi-Power® II B89 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 92 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
HCI Preferred Supplier 940177 Ball Valve, 1-1/2 in Nominal, FNPT End Style, Forged Brass Body, Full Port, PTFE Stem Seal Softgoods
HCI Preferred Supplier 940177 Ball Valve, 1-1/2 in Nominal, FNPT End Style, Forged Brass Body, Full Port, PTFE Stem Seal Softgoods
ECONOMY GM ENGINE BLUE SPRAY PAINT-KRYB27 >
