Gates® Power Transmission Hi-Power® II B145 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 148 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC72053291872
-
Manufacturer Part NumberB145
-
CountryUSA|Canada
-
Thickness13/32 in
-
MaterialEPDM
-
Top Width21/32 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter4.775 in
-
Section SizeB
-
Series9003
-
Number of Ribs1
-
Outside Length148 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
- Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather and aging
-
Alternative Part Number90032145
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission Hi-Power® II B145 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 148 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
Gates® Power Transmission Hi-Power® II B285 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 286 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
14 TOOTH H-PITCH QUICK DISCONNECT JA TIMING BELT SHEAVES-IDCQD14H150JA >
Gates® Power Transmission Tri-Power® PowerBand® 4/BX74 Heavy Duty Molded Notch V-Belt, BX Section, 21/32 in W Top, 77.6 in L Outside, 13/32 in THK, EPDM
Built for superior performance on heavy duty classical cross-section drives. The raw edge, Ethylene Elastomer construction and special notch design makes the Tri-Power belt especially suited for small diameter pulleys and back side idler drives.
Crosby Eye Bolt, Series: G-291, Measurement System: Imperial, 1/4 in Thread, 2 in Shank Length, Forged Steel, Hot Dipped Galvanized, 1/2 in ID Eye, 1 in OD Eye, UNC Thread, 3.06 in Overall Length, 650 lb Working Load, 1-1/2 in Thread Length
Fatigue rated at 1-1/2 times the working load limit at 20000 cycles
Hot dip galvanized after threading (UNC)
Furnished with standard hot dip galvanized hex nuts
Recommended for in-line pull
Importantly, these bolts meet other critical performance requirements including fatigue life, impact properties and material traceability
HCI Preferred Supplier 940171 Ball Valve, 1/4 in Nominal, FNPT End Style, Forged Brass Body, Full Port, PTFE Stem Seal Softgoods
HCI Preferred Supplier 940171 Ball Valve, 1/4 in Nominal, FNPT End Style, Forged Brass Body, Full Port, PTFE Stem Seal Softgoods
