Gates® Power Transmission Hi-Power® II B133 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 136 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC072053204681
-
Manufacturer Part NumberB133
-
CountryUSA
-
Thickness13/32 in
-
MaterialEPDM
-
Top Width21/32 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter4.775 in
-
Section SizeB
-
Series9003
-
Number of Ribs1
-
Outside Length136 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
- Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather and aging
-
Alternative Part Number90032133
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Catalog
-
Instruction/Installation Manual
-
Specification Sheet
Recently Viewed
Gates® Power Transmission Hi-Power® II B133 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 136 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
BrassCraft® ProCoat® CSSTNN-22N Gas Connector With 9/16-24 Fine Thread, 1/4 in, Flare Nut, 22 in L, Stainless Steel, Domestic
Utilizing advanced technologies, our ProCoat® yellow coating has been specifically engineered to withstand prolonged exposure to common household cleaning, plumbing repair and masonry chemicals, as well as the effects of harsh environmental influences such as salt and UV rays. ProCoat gas connectors are available in a variety of configurations.
Remke 7303-011R Insulated Wide Range Strain Relief Grip, 0.52 to 0.73 in Cable Openings, Steel
Tuff-Seal™ strain relief grips are used to connect cord or cable to electrical enclosures and equipment, power boxes, portable power tools, panel boards and machine tools. For indoor use only in dry locations, these grips help control arc-of-bend and prevent cable pull-out and damage resulting from flexing. Strain is distributed over the length of these grips instead of at a single point. These tuff seal strain relief grips are made with a single-weave, galvanized steel mesh and feature aluminum fittings and a gasket that provides an environmental seal against dust, filings and other foreign material.
ALFAGOMMA® B-0808-FJ9S B Series One-Piece Hose Fitting, 1/2 in Hose, 3/4-16 Connection, Hose x Female End Style, 46.4 mm Cutoff Allowance, Import
ALFAGOMMA® B-0808-FJ9S B Series One-Piece Hose Fitting, 1/2 in Hose, 3/4-16 Connection, Hose x Female End Style, 46.4 mm Cutoff Allowance, Import
Truflex® 4L400 Light Duty V-Belt, 4L Section, 1/2 in W Top, 40 in L Outside, 5/16 in THK
Gates® belts feature superior length stability for minimal take-up requirements.
Truflex® 4L310 Light Duty V-Belt, 4L Section, 1/2 in W Top, 31 in L Outside, 5/16 in THK
Gates® belts feature superior length stability for minimal take-up requirements.
