Gates® Power Transmission Hi-Power® II A50 Banded Classical Heavy Duty V-Belt, A Section, 1/2 in W Top, 52 in L Outside, 5/16 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC72053201802
-
Manufacturer Part NumberA50
-
CountryUSA|Canada
-
Thickness5/16 in
-
MaterialEPDM
-
Top Width1/2 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Classical Heavy Duty
-
Minimum Pulley Diameter4.138 in
-
Section SizeA
-
Series9002
-
Number of Ribs1
-
Outside Length52 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
- Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather and aging
| Competitor Name | Cross-Reference Number |
|---|---|
| Motion Industries | 00677646 |
-
Alternative Part Number90022050
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Instruction/Installation Manual
-
Catalog
-
Specification Sheet
Recently Viewed
Gates® Power Transmission Hi-Power® II A50 Banded Classical Heavy Duty V-Belt, A Section, 1/2 in W Top, 52 in L Outside, 5/16 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
SENGOKU CV-23K Convection Kerosene Heater, 23500 Btu/hr, Kerosene Fuel, 1.9 gal Tank
Our convection kerosene heater (23500 Btu) is safe and easy to use and economical to operate. It is great alternative heating source and excellent emergency heating source in events of power failure, no electricity is required. It provides efficient zone heating: up to 1000 sq-ft.
FYH® UCF212-39 4-Bolt Cylindrical Bore Normal Duty Square Flange Mount Ball Bearing Unit With Set Screw, 5/8 in Dia Bore, 5-5/8 in L Bolt Center-to-Center, 3/4 in Dia Bolt Circle
FYH® UCF212-39 4-Bolt Cylindrical Bore Normal Duty Square Flange Mount Ball Bearing Unit With Set Screw, 5/8 in Dia Bore, 5-5/8 in L Bolt Center-to-Center, 3/4 in Dia Bolt Circle
3.625" X 4.626X.438" RADIAL SHAFT, DOUBLE LIP, SOLID OIL SEAL. NITRILE RUBBER MATERIAL, CRWHA1 DESIGN.
1/2" CPVC TRANSITION FITTING USED WITH COMPRESSION FITTING TO ADAPT CPVC PIPE TO IPS OR COPPER TUBE. 1/2"-JWH412217 >
3/8"-HOSEX8-FEMALE FLAT FACE 90-MHDE0608FF90 >
