Gates® Power Transmission Hi-Power® II A136 Banded Classical Heavy Duty V-Belt, A Section, 1/2 in W Top, 138 in L Outside, 5/16 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC72053200966
-
Manufacturer Part NumberA136
-
CountryUSA|Canada
-
Thickness5/16 in
-
MaterialEPDM
-
Top Width1/2 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Classical Heavy Duty
-
Minimum Pulley Diameter4.138 in
-
Section SizeA
-
Series9002
-
Number of Ribs1
-
Outside Length138 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
- Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather and aging
| Competitor Name | Competitor Part Number |
|---|---|
| Motion Industries | 00678177 |
-
Alternative Part Number90022136
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Specification Sheet
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Gates® Power Transmission Hi-Power® II A136 Banded Classical Heavy Duty V-Belt, A Section, 1/2 in W Top, 138 in L Outside, 5/16 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
Browning® Classical Gripbelt® 1042217 AK Series Type 3 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 6.45 in OD, 6.4 in (A)/5.86 in (3L) Dia Pitch, 3/4 in W Face
Shaft mount reducers are enclosed helical gear reducers with a hollow output. They are mounted directly on the input shaft of the driven machine and are supported by the shaft and torque arm arrangement or motor mount frame. This eliminates the need for additional components to transmit torque from the reducer to the equipment.
Gates® Power Transmission Super HC® Molded Notch PowerBand® 5/3VX600 Heavy Duty Molded Notch V-Belt, 3VX Section, 3/8 in W Top, 60 in L Outside, 21/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
HCI Preferred Supplier 2406128 Reducer/Expander, 1-1/16-12 x 3/4-16 Nominal, SAE 37 deg Female JIC Flare x Male JIC Flare, Steel
HCI Preferred Supplier 2406128 Reducer/Expander, 1-1/16-12 x 3/4-16 Nominal, SAE 37 deg Female JIC Flare x Male JIC Flare, Steel
1 -MALE PIPE THREADX5 METAL GALVANIZED NIPPLE
