Sealmaster 2-15/16"-ID TAKE-UP BEARING UNITS SEA ST-47
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461006399
-
Manufacturer Part Number700761
-
CountryUSA
-
Load Capacity14839 lb Dynamic
-
Temperature Rating-20 to 220 deg F
-
FinishUncoated
-
TypeNon-Expansion Standard Duty
-
Height6-9/16 in
-
Width3-3/8 in
-
SeriesST Series
-
Bearing MaterialSteel
-
Length9-1/8 in
-
Bore Diameter2-15/16 in
-
Suitable For Use WithSTH-47 Center Pull Take Up Frames
- Take up housing type
- Seal flinger
- The Sealmaster exclusive locking pin and dimple system provides a direct lubricant path into the bearing cavity and ball path instead of around a lubrication groove
-
Alternative Part NumberST-47
-
UNSPSC31171533
-
Package DescriptionEACH
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
Streamlight® 65020 STYLUS® Handheld Penlight With Green LED, LED Bulb, Aluminum Housing, 7 Lumens
This ultra-slim penlight has a green LED perfect for tactical use and covert operation while preserving night vision.
MCR Safety 1211 Industrial Grade General Purpose Gloves, Gunn Cut/Wing Thumb Style, Cowhide Leather Palm, 7 ga Cotton Thread/Leather/Polyester, Gray, Safety Cuff, Resists: Abrasion and Wear, Fleece Lining
MCR Safety 1211 Industrial Grade General Purpose Gloves, Gunn Cut/Wing Thumb Style, Cowhide Leather Palm, 7 ga Cotton Thread/Leather/Polyester, Gray, Safety Cuff, Resists: Abrasion and Wear, Fleece Lining
Browning® 1171529 Single Strand Split Taper Bushed Type 4 Roller Chain Sprocket, 3/4 in Dia Bore, 17.628 in OD, #60 Chain, 72 Teeth, Steel
Browning® offers a variety of bushing type sprockets available in single and double strands. Offerings include 35 to 160 pitch range. Bushed type bore ranges are available from 1/2 to 5 in. Hardened teeth are available up to 30 teeth.
HCI Preferred Supplier 10107 Union, 5/16 in Nominal, SAE Male Flare Threaded UNF, Brass
HCI Preferred Supplier 10107 Union, 5/16 in Nominal, SAE Male Flare Threaded UNF, Brass
Proto® J72156 Socket Set, Imperial, 3/8 in, 1/2 in Drive, 10 Pieces, Black Oxide
