Sealmaster 1-15/16"-ID TAKE-UP BEARING UNITS SEA ST-31
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461006276
-
Manufacturer Part Number700748
-
CountryUSA
-
Load Capacity7889 lb Dynamic
-
Temperature Rating-20 to 220 deg F
-
FinishUncoated
-
TypeNon-Expansion Standard Duty
-
Height4-5/8 in
-
Width2-3/16 in
-
SeriesST Series
-
Bearing MaterialSteel
-
Length5-7/8 in
-
Bore Diameter1-15/16 in
-
Suitable For Use WithSTH-31 Center Pull Take Up Frames
- Sealmaster® has the industry's widest outer ring, the black oxided outer ring is 20 to 30% wider than industry standard outer rings
- 120 deg spaced, balanced 3-point contact minimizes inner ring distortion vibration, reduces noise and improves reliability
- The Sealmaster® unique land riding metal retainer design provides superior pocket clearance that allows for 360 deg grease circulation around the rolling elements resulting in better retained and utilized lubrication
- All bearings are assembled with a controlled housing fit between the bearing outer ring and housing bore
- Solid housing base
- Take up housing type
- Seal flinger
- The Sealmaster® exclusive locking pin and dimple system provides a direct lubricant path into the bearing cavity and ball path instead of around a lubrication groove
- The standard felt seal provides a tight labyrinth seal which retains lubrication and acts as a filter to exclude contamination
- Sealmaster® incorporates a unique heat treat process that hardens the inner race only where it is needed under the ball path
-
Alternative Part NumberST-31
-
UNSPSC31171533
-
Package DescriptionEACH
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
GP® 1243RD Standard and Deep Length Socket, 6 Points, 3/8 in Drive, 43 Pieces, Included Socket Size: 5/16 to 3/4 in, Molded Storage Case Container
GP® 1243RD Standard and Deep Length Socket, 6 Points, 3/8 in Drive, 43 Pieces, Included Socket Size: 5/16 to 3/4 in, Molded Storage Case Container
Dichtomatik 75115170 O-Ring, 134 Dash Number, 1.862 in ID x 2.068 in OD, PTFE, 55 Durometer, Import, Custom 134-TEFLON
O-rings are endless, ring shaped sealing elements with a circular cross-section that are manufactured from elastomer materials or PTFE. The designation of an O-ring is derived from the dimensions of its inner diameter and cord width in millimeters, along with the name of the material and its Shore A hardness.
TUNGSTEN CARBIDE BURR, 1/4" CYLINDRICAL(SA-1) - Solid carbide, double cut, made in USA. For smoothing, deburring, and shaping in hard-to-reach areas. Fits rotary drills and die grinders.
Drillco 350E002 3500E Imperial Plain Combined Drill and Countersink, 5/64 in Drill - Fraction, 0.0781 in Drill - Decimal Inch, 60 deg Included Angle, 60 deg Point Angle, HSS, Uncoated
When metal parts are machined on centers, as in turning or cylindrical grinding, it is always necessary to drill and countersink the center holes to serve as seats or bearings in the machine centers.
MCR Safety 9312 Regular Weight Cut-Resistant Sleeve, Universal, 12 in L x 7 ga THK, Steelcore® II/Polyester, White
MCR Safety Steelcore® ll 7-Gauge Cut Resistant Arm Sleeves Polyester Wrapped Stainless Steel 12 Inches x 6¼ Inches FDA-approved materials allow these sleeves to be used as kitchen cut-resistant sleeves Steelcore® II sleeves provide ultimate cut protection. Strands of stainless steel wrapped with polyester fiber add strength and comfort to this option. The 9312 is a 12-inch sleeve made with FDA-accepted material and can be used in food processing applications. These sleeves can be laundered without shrinkage and are ideal for use as cut-resistant sleeves in glass handling applications. Are you looking for the best cut-resistant sleeves? Look no further than MCR Safety's Steelcore® II series options! Individually polybagged.
