Sealmaster 1-11/16"-ID TAKE-UP BEARING UNITS SEA ST-27
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
-
BrandSealmaster®
-
UPC662461006238
-
Manufacturer Part Number700744
-
CountryUSA
-
Load Capacity7901 lb Dynamic
-
Temperature Rating-20 to 220 deg F
-
FinishUncoated
-
TypeNon-Expansion Standard Duty
-
Height4-5/8 in
-
Width2-3/16 in
-
SeriesST Series
-
Bearing MaterialSteel
-
Length5-11/16 in
-
Bore Diameter1-11/16 in
-
Suitable For Use WithSTH-27 Center Pull Take Up Frames
- Sealmaster® has the industry's widest outer ring, the black oxided outer ring is 20 to 30% wider than industry standard outer rings
- 120 deg spaced, balanced 3-point contact minimizes inner ring distortion vibration, reduces noise and improves reliability
- The Sealmaster® unique land riding metal retainer design provides superior pocket clearance that allows for 360 deg grease circulation around the rolling elements resulting in better retained and utilized lubrication
- All bearings are assembled with a controlled housing fit between the bearing outer ring and housing bore
- Solid housing base
- Take up housing type
- Seal flinger
- The Sealmaster® exclusive locking pin and dimple system provides a direct lubricant path into the bearing cavity and ball path instead of around a lubrication groove
- The standard felt seal provides a tight labyrinth seal which retains lubrication and acts as a filter to exclude contamination
- Sealmaster® incorporates a unique heat treat process that hardens the inner race only where it is needed under the ball path
-
Alternative Part NumberST-27
-
UNSPSC31171533
-
Package DescriptionEACH
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
GEARWRENCH® GearBox™ 85989 XL Series Extra Long Length Slim Double Box End Ratcheting Wrench Set, 17 Pieces, 8 to 25 mm, Polished Chrome
GEARWRENCH 85989 17-piece XL Gear Box Double Box End metric ratcheting wrench set consists of 1 of each 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 24 and 25mm XL GearBox™ ratcheting wrenches. Ratcheting box end need as little as 5-degrees to move the fastener as opposed to 30 degrees for standard box end wrenches. The standard box end combined with the long pattern length gives this wrench excellent torque capabilities to break a stubborn, rusted fastener. The ratcheting box end then makes the loosening or tightening of the fastener fast and safe. The box end features improved box end strength from GEARWRENCH's off-corner loading and at the same time, reduces fastener rounding. The double box end ratcheting wrenches are made from the finest chrome vanadium steel for precision long lasting tool life.
MORSE® 25047 1495 Plain Combined Drill and Countersink, 1/4 in Drill - Fraction, 0.25 in Drill - Decimal Inch, 60 deg Included Angle, 60 deg Point Angle, HSS, Bright
MORSE® 43117 1887 Ball Nose Center Cutting Regular Length Single End End Mill, 1/2 in Dia Cutter, 1 in Length of Cut, 2 Flutes, 1/2 in Dia Shank, 3 in OAL, Bright
CHAIN COUPLING-BRW10BCONN. >
Weiler® 13258 Single Row Cup Brush, 2-3/4 in Dia Brush, 5/8-11 Arbor Hole, 0.02 in Dia Filament/Wire, Standard/Twist Knot, Stainless Steel Fill
Weiler® 13258 Single Row Cup Brush, 2-3/4 in Dia Brush, 5/8-11 UNC Arbor Hole, 0.02 in Dia Filament/Wire, Standard/Twist Knot, Stainless Steel Fill
