IKO LRB263220 Inch Series Inner Ring With Oil Groove, 1-5/8 in ID x 2 in OD, 32 mm OAW, For Use With BR324120 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
-
BrandIKO
-
Manufacturer Part NumberLRB263220
-
CountryUSA
-
Lubrication Hole TypeOil
-
MaterialHigh Carbon Steel
-
Inside Diameter1-5/8 in
-
Bore TypeTapered
-
UNSPSC31171547
-
Catalog
Recently Viewed
IKO LRB263220 Inch Series Inner Ring With Oil Groove, 1-5/8 in ID x 2 in OD, 32 mm OAW, For Use With BR324120 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
Gates® Power Transmission Super HC® Molded Notch PowerBand® 5/3VX1400 Heavy Duty Molded Notch V-Belt, 3VX Section, 3/8 in W Top, 140 in L Outside, 21/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
Gates® Power Transmission Hi-Power® II B110 Banded Classical Heavy Duty V-Belt, B Section, 21/32 in W Top, 113 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
MCR Safety ST112AF Storm® Plus Single Lens Safety Glasses, Duramass® Anti-Fog, Gray Lens, Half-Frame Frame, Black, Nylon Frame, Polycarbonate Lens, ANSI Z87+, CE EN 166, CAN/CSA Z94.3
MCR Safety ST112AF Storm® Plus Single Lens Safety Glasses, Duramass® Anti-Fog, Gray Lens, Half-Frame Frame, Black, Nylon Frame, Polycarbonate Lens, ANSI Z87+, CE EN 166, CAN/CSA Z94.3
Milwaukee® 48-40-4510 Circular Saw Blade, 14 in Dia x 0.071 in THK, 1 in Arbor, Hardened Steel Blade, 90 Teeth
The MILWAUKEE® 14" 90T Dry Cut Carbide Tipped Metal Circular Saw Blades are specifically designed to exceed contractor's expectations for blade life, cut quality, and speed in the most demanding metal cutting applications – without a lubricant. The metal cutting circular saw blades have hand-tensioned hardened alloy steel bodies. This extends blade life and delivers the highest quality cuts available. The blades have Carbide-Tipped Teeth with Alternate Top Bevel grind to shear through metal delivering burr-free, cool-to-touch cuts.
Channellock® 728 Long Reach Diagonal Cutting Plier, 0.91 in L, 7-1/2 in OAL
Channellock® long reach pliers are specifically designed for those hard-to-reach jobs.

