Precision Deep Groove Ball Bearings
NSK is the World Leader in Deep Groove Ball Bearings. Deep Groove Ball Bearings (DGBB) are the most common form of rolling bearings and are used in a variety of applications, particularly those where high speeds and low power loss are required. NSK DGBB can handle not only radial forces, but also moderate axial loads in both directions. They are easy to install and can be deployed in a variety of configurations.
Gulf Bearing 3/8" DOUBLE-SHIELDED BALL BEARINGS GUL 1614-2-Z
Precision ground 1600® Series bearings are specially designed to provide a line of low cost yet high quality bearings for adaptation to a majority of precision bearing applications. They are made in easy to use inch dimensions and are recommended for medium loads and for maximum speeds in the range of 5000 rpm. The 1600® Series bearings are precision ground on all surfaces with exceptional care given to the ball grooves. Careful heat treatment provides a uniform and exact degree of hardness for maximum life. A ball retainer, or separator, is used to increase the range of allowable speeds by reducing ball-to-ball contact friction.
Gulf Bearing 7/16" DOUBLE-SEALED BALL BEARINGS GUL 1620-2-RS
Precision ground 1600® Series bearings are specially designed to provide a line of low cost yet high quality bearings for adaptation to a majority of precision bearing applications. They are made in easy to use inch dimensions and are recommended for medium loads and for maximum speeds in the range of 5000 rpm. The 1600® Series bearings are precision ground on all surfaces with exceptional care given to the ball grooves. Careful heat treatment provides a uniform and exact degree of hardness for maximum life. A ball retainer, or separator, is used to increase the range of allowable speeds by reducing ball-to-ball contact friction.
Gulf Bearing 7/16" DOUBLE-SHIELDED BALL BEARING GUL 1607-2-Z
Precision ground 1600® Series bearings are specially designed to provide a line of low cost yet high quality bearings for adaptation to a majority of precision bearing applications. They are made in easy to use inch dimensions and are recommended for medium loads and for maximum speeds in the range of 5000 rpm. The 1600® Series bearings are precision ground on all surfaces with exceptional care given to the ball grooves. Careful heat treatment provides a uniform and exact degree of hardness for maximum life. A ball retainer, or separator, is used to increase the range of allowable speeds by reducing ball-to-ball contact friction.
Nice® ER20 ER Series Non-Fill Slot Precision Deep Groove Ball Bearing With Extended Inner Ring, 1-1/4 in Dia Bore, 2.835 in OD, 1 Rows, 1-11/16 in W, 5755 lb Load
Recently Viewed
Proto® J4277B Rear Axle Flange Foot, For Use With Proto-Ease™ Master Puller, 5/8-12 in Dia Shaft, 1-7/32 in Thread
3-1/2" X 15-1/2" MEDIUM BELT-ARC53789 >
Browning® PB9205 Motor Base, For Use With TorqTaper® Plus Size 107-115SMTP/SMFP Ratio 5:1/9:1/15:1/25:1/35:1 Speed Reducer, Steel
A complete 1" drive set designed for servicing truck wheels. It contains a 13/16" square size for budd wheel inner cap nuts; a 1-1/2" outer budd nut size that has a controlled depth hex end to help prevent contact with the wheel; a 33mm size for 10 hole hub piloted wheels; three (3) deep thin wall sizes; and other regular length impact sockets. 6 Point sizes include: 7/8"; 15/16"; 1" and 1-3/16" standard length; 33mm deep; 1-1/16"; 1-1/8" and 1-1/4" thin;wall deep; 1-1/2" deep budd. 4 Point size includes: 13/16" sq
Set Contains 10 Pieces | 1" Drive 10 Piece Wheel Service Set | Molded Storage Case | Weight: 19.54 lbs.
COMPRESSION SPRINGS-WBJ30 >
Irwin® 12413 Countersink, 3/4 in Dia Body, 1/4 in Dia Shank, 5 Flutes, 82 deg Included, HSS
3/4", High Speed Steel, Countersink Drill Bit, Tip Is Milled & Precision Ground To 82 Degrees For Countersinking Into Most Machin able Materials, Engineered With Premium High Speed Steel With Black Oxide Coating For Corrosion Resistance, Features 5 Flutes For Reduced Vibration, 1/4" Round Shank.
