Browning 3-7/16"-ID 4-BOLT TRB PILLOW BLOCK BRW PBE-920F X 3-7/16
Browning® E920 series mounted tapered roller bearings feature durable 1-piece non-expansion housings with Type E mounting dimensions and limited misalignment. The E920 series contains setscrew locking collars for easy installation. It also contains a contact face riding seal in order to provide a good balance between contaminant entry, grease retention and friction. Depending on your application requirements, these bearings are available in a wide variety of bore sizes and housing configurations.
-
BrandBrowning®
-
UPC662289616855
-
Manufacturer Part Number730053
-
CountryUSA
-
Load Capacity15320 lb Dynamic
-
Locking DeviceDouble Set Screw Collar
-
Temperature Rating-20 to 200 deg F
-
FinishGray Painted
-
MaterialCast Iron
-
Maximum Speed1000 rpm
-
TypeHeavy Duty Type LN
-
Mounting TypeFour-Bolt Base
-
Seal TypeContact
-
SeriesPBE920
-
Base Width4-1/2 in
-
Base to Bore Centerline3-3/4 in
-
Bolt Center-to-Center Length9-11/16 to 11-7/16 in
-
Bore Diameter3-7/16 in
-
Bore TypeRound/Tapered
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height7-1/2 in
-
Overall Length14 in
-
Overall Width5 in
- Heavy duty tapered roller bearings with steel cage for radial, thrust and combined loading
- Single lip contact face-riding seals rotate with the shaft
- Double-collar interlock with 120 deg spacing setscrew lock, diamond faceted setscrews
- Powder coat epoxy 4-bolt cast iron housing
- Heavy duty tapered roller bearings with steel cage for radial, thrust and combined loading_x005f Single lip contact face-riding seals rotate with the shaft_x005f Double-collar interlock with 120 deg spacing setscrew lock, diamond faceted setscrews_x005f Powder coat epoxy 4-bolt cast iron housing
-
Alternative Part NumberPBE920FX 3 7/16
-
UNSPSC31171511
-
Package DescriptionEACH
-
Standards/ApprovalsAMBA Standard
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Browning 3-7/16"-ID 4-BOLT TRB PILLOW BLOCK BRW PBE-920F X 3-7/16
Browning® E920 series mounted tapered roller bearings feature durable 1-piece non-expansion housings with Type E mounting dimensions and limited misalignment. The E920 series contains setscrew locking collars for easy installation. It also contains a contact face riding seal in order to provide a good balance between contaminant entry, grease retention and friction. Depending on your application requirements, these bearings are available in a wide variety of bore sizes and housing configurations.
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
1-1/2-G-P 1-1/2" -male Pipe Thread Metal Galvanized Plug
1-1/2" -MALE PIPE THREAD METAL GALVANIZED PLUG-JPW11/2GP >
SANDING BELTS-SAI57303>
10" X 800' WHITE ROLL TOWELS CS/6 -WHY89460 >
3/8" X 12" Square Plain Keystock
