Dodge® 066230 215 Special Duty Pillow Block Roller Bearing Unit, 2-15/16 in Dia Bore, 11 to 12-1/2 in L Bolt Center-to-Center, 4-3/4 in Base to Bore Centerline, 14-1/4 in OAL x 9.88 in OAH
Dodge® 066230 215 Special Duty Pillow Block Roller Bearing Unit, 2-15/16 in Dia Bore, 11 to 12-1/2 in L Bolt Center-to-Center, 4-3/4 in Base to Bore Centerline, 14-1/4 in OAL x 9.88 in OAH
-
BrandDodge®
-
UPC782475035830
-
Manufacturer Part Number066230
-
CountryUSA
-
Load Capacity21331 lb Dynamic
-
Locking DeviceAdapter Mounted
-
FinishBlack Oxide
-
MaterialCast Iron
-
Maximum Speed1830 rpm
-
TypeSpecial Duty
-
Mounting TypeTwo-Bolt Base
-
Seal TypePiston Ring
-
Series215
-
Base Width4-3/4 in
-
Base to Bore Centerline4-3/4 in
-
Bolt Center-to-Center Length11 to 12-1/2 in
-
Bore Diameter2-15/16 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height9.88 in
-
Overall Length14-1/4 in
-
Overall Width5-3/4 in
- Quality duplex tapered roller bearing
- Effective piston ring seals
- Rugged two-piece housing
- Elongated bolt holes
| Competitor Name | Competitor Part Number |
|---|---|
| Applied Industrial Technologies | 100940683 |
| Motion Industries | 00574845 |
-
Alternative Part NumberP2B-SD-215
-
UNSPSC31171511
-
Standards/ApprovalsUL Listed
-
Catalog
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Dodge® 066230 215 Special Duty Pillow Block Roller Bearing Unit, 2-15/16 in Dia Bore, 11 to 12-1/2 in L Bolt Center-to-Center, 4-3/4 in Base to Bore Centerline, 14-1/4 in OAL x 9.88 in OAH
Dodge® 066230 215 Special Duty Pillow Block Roller Bearing Unit, 2-15/16 in Dia Bore, 11 to 12-1/2 in L Bolt Center-to-Center, 4-3/4 in Base to Bore Centerline, 14-1/4 in OAL x 9.88 in OAH
15 TOOTH SPROCKETS FOR #60 CHAIN
Leviton® 13357 Lampholder, 660 W Lamp, 600 VAC, Medium Bi-Pin Fluorescent Lamp
Drillco 77A132C 7700 Center Cutting Imperial Regular Length Single End Ball Nose End Mill, 1/2 in Dia Cutter, 1 in Length of Cut, 4 Flutes, 1/2 in Dia Shank, 3 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.
Legris by Dixon® 1094U56R00 Tubing, 0.16 in ID x 1/4 in OD x 100 ft L x 0.045 in THK Wall, Polyurethane, Domestic
Legris by Dixon® 1094U56R00 Tubing, 0.16 in ID x 1/4 in OD x 100 ft L x 0.045 in THK Wall, Polyurethane, Domestic
HCI Preferred Supplier 80512 Pressure Gauge, 0 to 30 psi Pressure, 1/8 in Connection, 1-1/2 in Dia Dial
HCI Preferred Supplier 80512 Pressure Gauge, 0 to 30 psi Pressure, 1/8 in Connection, 1-1/2 in Dia Dial
