Dodge® 041864 Type USAF Pillow Block Roller Bearing Unit, 2-15/16 in Dia Bore, 9.88 to 11 in L Bolt Center-to-Center, 12.59 in OAL x 7.38 in OAH
Dodge® 041864 Type USAF Pillow Block Roller Bearing Unit, 2-15/16 in Dia Bore, 9.88 to 11 in L Bolt Center-to-Center, 12.59 in OAL x 7.38 in OAH
-
BrandDodge®
-
UPC782475021048
-
Manufacturer Part Number041864
-
CountryUSA
-
Load Capacity68000 lb Dynamic/73500 lb Static
-
Locking DeviceAdapter Mounted
-
FinishUncoated
-
MaterialCast Iron
-
Maximum Speed3000 rpm
-
TypeType USAF
-
Mounting TypeTwo-Bolt Base
-
Seal TypeTriple-Tect™
-
Bolt Center-to-Center Length9.88 to 11 in
-
Bore Diameter2-15/16 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height7.38 in
-
Overall Length12.59 in
- Cast-in dimples locate drill holes for lube fittings, vents, sensors and mounting modifications
- Housing base is threaded to accept four grade five cap bolts for added strength that match base bolts for one-wrench installation
- Standard housings have two oversized drains adaptable to circulating oil systems
- Pry slots allow easy separation of the pillow block
- Cap bolts match base bolts for one-wrench installation
- USAF housings also match standard dimensions to assure interchangeability
| Competitor Name | Cross-Reference Number |
|---|---|
| Applied Industrial Technologies | 100942032 |
| Motion Industries | 02387824 |
-
Alternative Part NumberP2B517-USAF-215TT
-
UNSPSC31171511
-
Standards/ApprovalsUL Listed
-
Instruction/Installation Manual
-
Catalog
-
Specification Sheet
Recently Viewed
Dodge® 041864 Type USAF Pillow Block Roller Bearing Unit, 2-15/16 in Dia Bore, 9.88 to 11 in L Bolt Center-to-Center, 12.59 in OAL x 7.38 in OAH
Dodge® 041864 Type USAF Pillow Block Roller Bearing Unit, 2-15/16 in Dia Bore, 9.88 to 11 in L Bolt Center-to-Center, 12.59 in OAL x 7.38 in OAH
THE STANDARD TRAPEZOIDAL TOOTH TIMING BELT DESIGN PERFORMS POORLY IN HIGH TORQUE APPLICATIONS AND HIGH-POWER DRIVES AT LOWER SPEEDS. TO OVERCOME THIS DISADVANTAGE THE HIGH TORQUE BELT (HTB) WAS DEVELOPED USING A MORE EFFICIENT TOOTH PROFILE. OIL, HEAT AND ABRASION-RESISTANT
-JAS14408M20 >
JASON AX48 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 51" OUTSIDE LENGTH
COGGED RAW EDGE V-BELT. POLYESTER CORD REINFORCEMENT. RAW EDGE SIDEWALLS ELIMINATE SLIPPAGE AND INCREASES EFFICIENCY. COGGED DESIGN ALLOWS FOR GREATER HEAT DISSIPATION. THE BELT IS OIL AND HEAT RESISTAND AND CONFORMS TO ARPM STANDARD IP 20
'-JASAX48 >
JASON 430H200 SYNCHRONOUS BELT, 1/2 " PITCH; 43" PITCH LENGTH 1-1/2" BELT WIDTH. 86 TEETH
SYNTHETIC RUBBER TIMING BELT. CONFORMS TO RMA ENGINEERING STANDARD. TIMING BELTS ARE MEASURED BY LENGTH, TOOTH PITCH, THEN WIDTH. THE FIRST NUMBER IS THE LENGTH, THE LETTER AND SOMETIME NUMBER REFER TO THE TOOTH AND THE FINAL NUMBER IS THE WIDTH. STANDARD TIMING TOOTH PROFILE, H; FIBERGLASS TENSIILE MATERIAL; RUBBER OUTER MATERIAL
-JAS430H100 >
TAPERED ROLLER BEARING CONE-NTNJLM813049 >
40-B-22-F-3/4 22 Tooth Sprockets For #40
22 TOOTH SPROCKETS FOR #40 CHAIN-IDC40B22F3/4 >
