FYH® UCP206-20 Pillow Block Unit, 1-1/4 in Dia Bore, 4-3/4 in L Bolt Center-to-Center
FYH® UCP206-20 Pillow Block Unit, 1-1/4 in Dia Bore, 4-3/4 in L Bolt Center-to-Center
-
BrandFYH®
-
UPC808250109142
-
Manufacturer Part NumberUCP206-20
-
CountryUSA
-
Load Capacity4388 lbf Dynamic/2543 lbf Static
-
Locking DeviceSet Screw
-
MaterialCast Iron
-
SeriesUCP
-
Bolt Center-to-Center Length4-3/4 in
-
Bore Diameter1-1/4 in
-
Bore TypeCylindrical
- P206 housing
- UC206-20 bearing
- Pillow block unit with a rigid cast iron housing and two specially designed set screws in the inner ring spaced at 120 deg for maximum holding power and reliability for a wide variety of applications and operating conditions
- 1/2 in bolt
- 6-1/2 in OAW
- 3-5/16 in OAH
- Basic Load Rating: 13.9 factor
- 1-7/8 in base depth
- 1-11/16 in center to base
- 1/4-28 UNF set screw size
- A-1/4-28 UNF grease fitting size
-
UNSPSC31171511
-
Catalog
Recently Viewed
FYH® UCP206-20 Pillow Block Unit, 1-1/4 in Dia Bore, 4-3/4 in L Bolt Center-to-Center
FYH® UCP206-20 Pillow Block Unit, 1-1/4 in Dia Bore, 4-3/4 in L Bolt Center-to-Center
ALE 1-THHN-BLK THHN BUILDING WIRE-1 AWG-BLACK-STRANDED CONDUCTOR.
THHN WIRE IS PRIMARILY USED IN CONDUIT AND CABLE TRAYS FOR SERVICES, FEEDERS, AND BRANCH CIRCUITS IN COMMERCIAL OR INDUSTRIAL APPLICATIONS AS SPECIFIED IN THE NATIONAL ELECTRICAL CODE, 1 GAUGE, BLACK STRANDED CONDUCTOR.
- ALE1THHNBLK >
Browning® 3546991 TGC Cam Detent Mini Straight Bushing Overload Clutch, 1/2 in Dia Bore, 3.15 in OD, 23 to 56 in-lb Torque, 2.36 in OAL
The Browning® Torq/Gard® overload clutches are one of the most popular torque overload devices that power transmission solutions offers. A spring loaded cam follower seated in a single hub cam detent cause the hub and clutch to rotate together. Therefore, the clutch always resets in the same position if tripped, staying in phase. They can be turned in both directions by design. After tripping, the unit automatically resets when it returns to the set position. This is usually performed by jogging the machine after the jam or overload is cleared. Shaft bushings are used to accommodate a standard maximum bore unit to the application shaft requirement. Torque capacity up to 8000 in-lb and speed ranges from 350 to 1800 rpm.
Browning® 3748381 Taper Lock Bushing, 9/16 in Dia Bore, 1-25/64 in Dia Barrel, 7/8 in OAL, Steel
Browning® 3748381 Taper Lock Bushing, 9/16 in Dia Bore, 1-25/64 in Dia Barrel, 7/8 in OAL, Steel
DeWALT® by Radians® DPG35XL DPG35 Breathable Work Gloves, XL, 15 ga Nylon Shell/Nitrile, Gray, Knit Wrist Cuff, Nitrile Coating, Resists: Abrasion, Cut, Tear, Puncture and Water
The DeWALT® DPG35 full dip water-resistant Breathable Work Glove has a fully coated nitrile 15 ga nylon shell which is highly water-resistant but the breathable material allows sweat to evaporate instead of staying inside the glove.
Dutton-Lainson® 491 Fuel Filter Wrench, 6 in L, For Use With Goldenrod® Fuel Tank Filters, Plastic
Dutton-Lainson® 491 Fuel Filter Wrench, 6 in L, For Use With Goldenrod® Fuel Tank Filters, Plastic
