Duracell® DLCR2BPK Cylindrical Battery, Lithium-Manganese Dioxide, 3 VDC Nominal, 750 mAh Nominal, CR2, 3.2 to 3.3 VDC Charge
Duracell® DLCR2BPK Cylindrical Battery, Lithium-Manganese Dioxide, 3 VDC Nominal, 750 mAh Nominal, CR2, 3.2 to 3.3 VDC Charge
-
BrandDuracell®
-
UPC041333005102
-
Manufacturer Part NumberDLCR2BPK
-
CountryUSA
-
Terminal TypeFlat
-
Maximum Discharge Current1000 mA
-
Charge Voltage3.2 to 3.3 VDC
-
Chemical SystemLithium-Manganese Dioxide
-
Nominal Capacity750 mAh
-
Nominal Voltage3 VDC
-
Shelf Life10 years
-
Battery SizeCR2
-
Dimensions15.6 mm Dia x 27 mm H
-
Discharge Cut-Off Voltage2.3 VDC
-
Internal Impedance0.3 Ohm
-
Life Hour1/2 hr
- 5.168 cu-cm volume
- -20 to 75 deg C operating temperature
- 2.3 V at 1000 mA cut-off voltage
- 1000 mA at 2.3 VDC discharge current
| Cross-Reference Number |
|---|
| 842575 |
-
UNSPSC26111711
-
Standards/ApprovalsANSI/NEDA 5046LC
-
Specification Sheet
Recently Viewed
Duracell® DLCR2BPK Cylindrical Battery, Lithium-Manganese Dioxide, 3 VDC Nominal, 750 mAh Nominal, CR2, 3.2 to 3.3 VDC Charge
Duracell® DLCR2BPK Cylindrical Battery, Lithium-Manganese Dioxide, 3 VDC Nominal, 750 mAh Nominal, CR2, 3.2 to 3.3 VDC Charge
Dodge® 046431 H31 Adapter Assembly, 4-17/16 in Dia Shaft, 6-3/4 in OD
Dodge® 046431 H31 Adapter Assembly, 4-17/16 in Dia Shaft, 6-3/4 in Dia Outside
12/2-GAUGE SPEAKER WIRE--RL/250'-JWH548804>
Leviton® 223 Duplex Non-Grounding Straight Blade Receptacle With Ears, 125 V AC, 15 A, 2 Poles, 2 Wires, Brown
Leviton® 223 Duplex Non-Grounding Straight Blade Receptacle With Ears, 125 VAC, 15 A, 2 Poles, 2 Wires, Brown
Dixon 600-A-AL 20 Cam and Groove Fitting, 6 in Nominal, Male Adapter x Female Male Adapter x FNPT End Style, Aluminum
HCI Preferred Supplier 61920 Cam and Groove Fitting, 6 in Nominal, Male Adapter x Female Male Adapter x FNPT End Style, Aluminum
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Metric-type LRT series Inner Rings have shaft diameters from 5 to 440 mm.
