Duracell® Coppertop® MN918 Rectangular Lantern Battery, Zinc-Manganese Dioxide, 6 VDC, 27 Ah, Lantern
Duracell® Coppertop® MN918 Rectangular Lantern Battery, Zinc-Manganese Dioxide, 6 VDC, 27 Ah, Lantern
-
BrandDuracell®
-
UPC041333091068
-
Manufacturer Part NumberMN918
-
CountryUSA
-
Terminal TypeScrew
-
Chemical SystemZinc-Manganese Dioxide
-
TypeRectangular
-
Nominal Capacity27 Ah
-
Nominal Voltage6 VDC
-
Shelf Life6 to 8 years
-
Battery SizeLantern
-
Dimensions136.5 mm L x 73 mm W x 127 mm H
-
Discharge Cut-Off Voltage6 VDC
-
Internal Impedance330 mOhm
-
Life Hour780 hr
- Delivered capacity is dependent on the applied load, operating temperature and cut-off voltage
- -20 to 54 deg C operating temperature
- 1074 cu-cm volume
- 780 hr at 6 V, 110 Ohm Life Hours
- 6 V at 110 Ohm, 780 hr, 21 deg C discharge cut-off voltage
-
UNSPSC26111702
-
Standards/ApprovalsANSI 918A|IEC 4LR25-2
-
SDS
-
Specification Sheet
Recently Viewed
Duracell® Coppertop® MN918 Rectangular Lantern Battery, Zinc-Manganese Dioxide, 6 VDC, 27 Ah, Lantern
Duracell® Coppertop® MN918 Rectangular Lantern Battery, Zinc-Manganese Dioxide, 6 VDC, 27 Ah, Lantern
Keep your scissors safe and secure in this durable leather scissors holder. This lightweight holder fits a variety of electrician's scissors. Tunnel loop fits belts up to up to 1-1/2-Inch (38 mm) wide. Quality constructed for long life.
Greenlee® 645-1-7/32 Quick-Change Hole Cutter, 1-7/32 in Dia, 8 ga D Cutting, Tungsten Carbide Tip Cutting Edge, 3/8 in Arbor
Greenlee® 645-1-7/32 Quick-Change Hole Cutter, 1-7/32 in Dia, 8 ga D Cutting, Tungsten Carbide Tip Cutting Edge, 3/8 in Arbor
MARXMAN™ 85000 330QI General Purpose Jobber Length Drill Bit, 1/16 in Drill - Fraction, 0.0625 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MARXMAN™ 85000 330QI General Purpose Jobber Length Drill Bit, 1/16 in Drill - Fraction, 0.0625 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MORSE® 51137 5374 Standard Length Jobber Length Drill Bit, 31/64 in Drill - Fraction, 0.4844 in Drill - Decimal Inch, 118 deg Point, Solid Carbide, Bright
MORSE® 51137 5374 Standard Length Jobber Length Drill Bit, 31/64 in Drill - Fraction, 0.4844 in Drill - Decimal Inch, 118 deg Point, Solid Carbide, Bright
MORSE® 91465 1330G General Purpose Jobber Length Drill Bit, O Drill - Letter, 0.316 in Drill - Decimal Inch, 118 deg Point, HSS, TiN Coated
MORSE® 91465 1330G General Purpose Jobber Length Drill Bit, O Drill - Letter, 0.316 in Drill - Decimal Inch, 118 deg Point, HSS, TiN Coated
