OIL SEALS
3.500" X 4.626" X.438" SINGLE LIP SHAFT SEAL WITH SPRING. CRWH1 SEALS ARE DESIGNED WITH A DOUBLE METAL CASE, AND SKF WAVE LIP MADE OF ELASTOMER WITH A HIGHER PUMPING RATE TO REDUCE HEAT GENERATION, AND A GARTER SPRING TO OPTIMIZE SEALING AGAINST THE SHAFT.
3.500" X 4.842" X.903" SCOTSEALS. Steer Axle Wheel, Oil, Seal Replaces For 35058 / 35059 370001A, 308-0836
Nitrile Rubber Wheel End Component
3 in Shaft Diameter
4 in Housing Bore Diameter
Front Wheel Seal, 4.848" O.D, 3.500" I.D, Commonly Used On Ford Trucks/Buses
3.500" X 4.842X.904 SCOTSEAL, NITIRILE RUBBER WHEEL END COMPONENT
3.500" X 4.852" X .904" FRONT AXLE / TRACTOR/SCOTSEAL- INCH
3.500" X 5.000" X .891" SCOTSEAL HEAVY TRUCK, WHEEL END SEAL
3.500" X 5.251" X .438" NBR, SINGLE LIP, WAVE OIL SEAL, BORE-TITE
3.563" X 4.501" X .438" RADIAL SHAFT, SINGLE LIP, SOLID OIL SEAL. NITRILE RUBBER MATERIAL, CRWH1 DESIGN.
3.625" X 4.626X.438" RADIAL SHAFT, DOUBLE LIP, SOLID OIL SEAL. NITRILE RUBBER MATERIAL, CRWHA1 DESIGN.
3.625" X 4.751" X .438" SINGLE LIP RADIAL SHAFT SEAL WITH DOUBLE METAL CASE.
3.625" X 4.876X.438" RADIAL SHAFT, SINGLE LIP, SOLID OIL SEAL. NITIRLE RUBBER MATERIAL CRWH1 DESIGN.
3.625" X 4.999" X .375"-FRONT AXLE SHAFT RADIAL SHAFT OIL SEAL
3.625" X 4.999" X .438" RADIAL SHAFT, SINGLE LIP, SOLID OIL SEAL. NITIRILE RUBBER MATERIAL CRWH1 DESIGN.
SCOTSEALS-3.625" X 5.001" X .891" NITRILE RUBBER WHEEL END COMPENENT.
.375" X .749" X .250" SINGLE LIP SHAFT SEAL WITH SPRING.
3.750" X 4.501" X .469" RADIAL SHAFT SEAL WITH DOUBLE METAL CASE. SKF WAVE LIP AND AUXILLIARY, NON-CONTACTING LIP CRWHA1 DESIGN.
3.750" X 4.751" X .375" RADIAL SHAFT SEAL WITH METAL CASE AND SKF WAVE LIP
3.750" X 4.751" X .438"RADIAL SHAFT, DOUBLE LIP, SOLID OIL SEALS. POLYACRYLATE ELASTOMER MATERIAL CRWA1 DESIGN
3.750" X 4.999" X .438" RADIAL SHAFT, DOUBLE LIP, SOLID SOIL SEAL. NITRILE RUBBER MATERIAL CRWHA1 DESIGN.
CRSEAL 38220 / 3.813X5.251X0.469 CRSH1 R ; SGL LIP SEAL
Lip Seal; 3-13/16" Shaft Dia; 5-1/4" Housing Bore; 0.469" Nominal Width; Nitrile Lip; Solid Seal; 15/32" Actual Width; Spring Loaded; 1 Sealing Lips; Carbon Steel Garter Lip Retainer; Steel Case; CRSH1 Seal Design Code
3.875" X 5.251" X .438"-RADIAL SHAFT, SINGLE LIP, SOLID OIL SEAL. NITRILE RUBBER MATERIAL CRWH1 DESIGN.
3.937" X 4.724" X .472"RADIAL SHAFT, SINGLE LIP WITH SPRING. FLUORO RUBBER MATERIAL CRW1 DESIGN
3.938" X 4.999" X .438"SINGLE LIP SHAFT SEAL WITH SPRING. NITRILE RUBBER LIP MATERIAL, SKF WAVE SEAL.
Recently Viewed
Weiler® 44021 Mop Handle Brace, Steel
1/4" SOCK-IT-OUT TAP EXTRACTOR - PDTKS55AC250L>
THIN SERIES BALL BEARING-NTN16004 >
MORSE® 43555 1897 Non-Center Cutting Regular Length Single End End Mill, 1-1/8 in Dia Cutter, 1-1/2 in Length of Cut, 6 Flutes, 3/4 in Dia Shank, 3-7/8 in OAL, Bright
Apex® MDC-08 Magnetic Nutsetter, Hex Point, 2-9/16 in OAL, Alloy Steel
Browning® 767764 VPE 100 Intermediate Duty Pillow Block Ball Bearing, 3/4 in Dia Bore, 3-3/8 to 4-3/16 in L Bolt Center-to-Center, 1-5/16 in Base to Bore Centerline, 5 in OAL x 2-17/32 in OAH
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric, or BOA concentric locking collar. The contact seal, with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction. Depending on your preference, these bearings are available in inch and metric bore with a wide variety of cast iron, stamped steel or rubber mount housings or specific industry solutions as illustrated on the pages to follow.
