V-BELTS COGGED AX-BX-CX-DX
NOTCHED GRIP V-BELTS-BRWCX136>
NOTCHED GRIP V-BELT-JASCX136>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >148-JASCX144 >
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 148-PIXCX144 >
NOTCHED GRIP V-BELT-JASCX150>
NOTCHED GRIP V-BELT-JASCX158>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 162-PIXCX158 >
NOTCHED GRIP V-BELT-JASCX173>
NOTCHED GRIP V-BELTS-BRWCX180>
NOTCHED GRIP V-BELTS-BRWCX240>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >72-JASCX68 >
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 79"-PIXCX75 >
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 85"-PIXCX81 >
NOTCHED GRIP V-BELTS-BRWCX85>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >90"-JASCX86 >
NOTCHED GRIP V-BELTS-JASCX90>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 94'-PIXCX90 >
NOTCHED GRIP V-BELT-JASCX96>
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 100"-PIXCX96 >
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >183-JASBX180 >
JASON AX48 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 51" OUTSIDE LENGTH
COGGED RAW EDGE V-BELT. POLYESTER CORD REINFORCEMENT. RAW EDGE SIDEWALLS ELIMINATE SLIPPAGE AND INCREASES EFFICIENCY. COGGED DESIGN ALLOWS FOR GREATER HEAT DISSIPATION. THE BELT IS OIL AND HEAT RESISTAND AND CONFORMS TO ARPM STANDARD IP 20
'-JASAX48 >
JASON AX52 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 54" OUTSIDE LENGTH
AX SECTION COGGED CLASSICAL V-BELT. CONFORMS TO ARPM STANDARDS IP-20. THE COGGED RAW EDGE V-BELTS ARE DESIGNATED BY A LETTER INDICATING BELT SECTION, FOLLOWED BY "X" WHICH SIGNIFIES COGGED, RAW-EDGE CONSTRUCTION THAT HAS GREATER POWER CAPACITY THAN STANDARD WRAPPED CONSTRUCTION. INSIDE LENTH PLUS 2 " EQUALS OUTSIDE LENGTH
-JASAX52>
JASON AX53 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 55" OUTSIDE LENGTH
COGGED CLASSICAL V-BELT. 1/2 " TOP WIDTH. 5/16 " THICK. THIS IS A CLASSICAL SERIES BELT, WHICH IS MUCH HIGHER QUALITY AND STRONGER THAN An FHP BELT WITH THE SAME MEASUREMENTS.
-JASAX53 >
JASON AX55 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 57" OUTSIDE LENGTH
V-BELT, RUBBER, 1/2" X 57" OC. THE LOWER COMPRESSION SECTION OF THE BELT IS MADE OF HIGHLY FIBER REINFORCED, OIL AND HEAT RESISTANT.
-JASAX55 >
Recently Viewed
1/2" X 2-1/2" Stainless Steel Socket Head Set Screws
MORSEĀ® 14915 1398 1-Stage Type C Heavy Duty Screw Machine Aircraft Drill, #31 Drill - Wire, 0.12 in Drill - Decimal Inch, 135 deg Point, HSS
Drillco 1000E219 Imperial Silver and Deming Drill, 1-19/64 in Drill - Fraction, 1.2969 in Drill - Decimal Inch, 1/2 in Shank, HSS
1000E series S&D Drills expand the size range capacity of a 1/2" portable drill chuck.Ā Common flute and overall length for minimal adjustment during tool changes. Ideal for drilling low and medium tensile strength materials.
CoilhoseĀ® TGC090 Inflator Gauge, Ladder Gauge, Straight Chuck, Fine Thread, 12 in L Thread, Brass/Die Cast Zinc/Nitrile, Domestic
CoilhoseĀ® TGC090 Inflator Gauge, Ladder Gauge, Straight Chuck, Fine Thread, 12 in L Thread, Brass/Die Cast Zinc/Nitrile, Domestic
GreenleeĀ® 645-1-3/8 Quick-Change Hole Cutter, 1-3/8 in Dia, 8 ga D Cutting, Tungsten Carbide Tip Cutting Edge, 3/8 in Arbor
GreenleeĀ® 645-1-3/8 Quick-Change Hole Cutter, 1-3/8 in Dia, 8 ga D Cutting, Tungsten Carbide Tip Cutting Edge, 3/8 in Arbor
JacobsĀ® 30825D T-Handle Chuck Key, 15/64 in Dia Pilot, Key Number: K30, For Use With 1/4 in, 3/8 in and 1/2 in Chucks, Soft Steel
JacobsĀ® 30825D T-Handle Chuck Key, 15/64 in Dia Pilot, Key Number: K30, For Use With 1/4 in, 3/8 in and 1/2 in Chucks, Soft Steel
