V-BELTS COGGED AX-BX-CX-DX
CX-144 JASON INDUSTRIAL PRODUCTS
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >148-JASCX144 >
CX-144 PIX BELTS
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 148-PIXCX144 >
CX-158 PIX BELTS
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 162-PIXCX158 >
CX-68 JASON INDUSTRIAL PRODUCTS
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >72-JASCX68 >
CX-75 PIX BELTS
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 79"-PIXCX75 >
CX-81 PIX BELTS
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 85"-PIXCX81 >
CX-86 JASON INDUSTRIAL PRODUCTS
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >90"-JASCX86 >
CX-90 PIX BELTS
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 94'-PIXCX90 >
CX-96 PIX BELTS
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE 100"-PIXCX96 >
JASBX180 JASON INDUSTRIAL PRODUCTS
NOTCHED GRIP V-BELT OUTSIDE CIRCUMFERENCE >183-JASBX180 >
JASON AX48 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 51" OUTSIDE LENGTH
COGGED RAW EDGE V-BELT. POLYESTER CORD REINFORCEMENT. RAW EDGE SIDEWALLS ELIMINATE SLIPPAGE AND INCREASES EFFICIENCY. COGGED DESIGN ALLOWS FOR GREATER HEAT DISSIPATION. THE BELT IS OIL AND HEAT RESISTAND AND CONFORMS TO ARPM STANDARD IP 20
'-JASAX48 >
JASON AX52 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 54" OUTSIDE LENGTH
AX SECTION COGGED CLASSICAL V-BELT. CONFORMS TO ARPM STANDARDS IP-20. THE COGGED RAW EDGE V-BELTS ARE DESIGNATED BY A LETTER INDICATING BELT SECTION, FOLLOWED BY "X" WHICH SIGNIFIES COGGED, RAW-EDGE CONSTRUCTION THAT HAS GREATER POWER CAPACITY THAN STANDARD WRAPPED CONSTRUCTION. INSIDE LENTH PLUS 2 " EQUALS OUTSIDE LENGTH
-JASAX52>
JASON AX53 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 55" OUTSIDE LENGTH
COGGED CLASSICAL V-BELT. 1/2 " TOP WIDTH. 5/16 " THICK. THIS IS A CLASSICAL SERIES BELT, WHICH IS MUCH HIGHER QUALITY AND STRONGER THAN An FHP BELT WITH THE SAME MEASUREMENTS.
-JASAX53 >
JASON AX55 COGGED CLASSICAL V-BELTS. 1/2" TOP WIDTH, 5/16" THICK, 57" OUTSIDE LENGTH
V-BELT, RUBBER, 1/2" X 57" OC. THE LOWER COMPRESSION SECTION OF THE BELT IS MADE OF HIGHLY FIBER REINFORCED, OIL AND HEAT RESISTANT.
-JASAX55 >
Recently Viewed
1-11/16"-ID SPHERICAL-OD INSERT BEARING - FAFRA111RAB>
IKO BHA1012ZOH Inch Series Caged Heavy Duty Shell Standard Needle Roller Bearing With Oil Hole and Dust Cover, 5/8 in Dia Bore, 7/8 in OD, 1 Row, 3/4 in W, 12700 N Dynamic/18500 N Static Load
IKO manufactures a wide range of radial Needle Roller Bearings to meet the needs of different applications and machine profiles. These include shell type bearings, needle roller cages for both general use and within engine connecting rods and machined type Needle Roller Bearings. Shell type Needle Roller Bearings are lightweight, low profile motion components designed to handle either high speeds or heavy loads, depending on the configuration. An outer ring made of high strength steel enables a streamlined profile with the lowest sectional height of all the Needle Roller Bearings.
POWERATED FHP V-BELT >(5-L-380)-GAT6938 >
BEARINGS-TAPERED ROLLER BEARING SETS-CHIKR12051Z>
22220 Str-ID Spherical Roller
STR-ID SPHERICAL ROLLER BEARINGS-FAG22220>
