Chicago Pneumatic CP-9887 Pneumatic Drill, 3/8 in Chuck, 1/2 hp, 25.784 to 27 cfm Air Flow, 8 in OAL
Chicago Pneumatic T025376 Pneumatic Drill, 3/8 in Chuck, 1/2 hp, 25.784 to 27 cfm Air Flow, 8 in OAL
-
BrandChicago Pneumatic
-
UPC015451537609
-
Manufacturer Part NumberT025376
-
CountryUSA
-
Tool/KitBare Tool
-
Chuck Size3/8 in
-
Minimum Hose Size3/8 in
-
Air Flow Rate25.784 to 27 cfm
-
Air Inlet1/4 in
-
Horsepower1/2 hp
-
Sound Level110 dBA Power/99 dBA Pressure
-
Speed2800 rpm
-
Overall Length8 in
- Power and speed for general maintenance
- Great productivity
- Good for vertical drilling and to reach confined areas
- Built-in regulator for efficient contro
-
Alternative Part NumberCP887
-
UNSPSC27131505
-
Package Description1/PK
-
Standards/ApprovalsISO-28927-5|PROP65: This Product can expose you to chemicals including lead, which is known to the state of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
-
Instruction/Installation Manual
Recently Viewed
Chicago Pneumatic CP-9887 Pneumatic Drill, 3/8 in Chuck, 1/2 hp, 25.784 to 27 cfm Air Flow, 8 in OAL
Chicago Pneumatic T025376 Pneumatic Drill, 3/8 in Chuck, 1/2 hp, 25.784 to 27 cfm Air Flow, 8 in OAL
HCI Preferred Supplier 840500 T-Bolt Clamp, 5 in Nominal, 4-25/32 to 5-1/16 in OD x 0.025 in THK, 301 Stainless Steel Band
HCI Preferred Supplier 840500 T-Bolt Clamp, 5 in Nominal, 4-25/32 to 5-1/16 in OD x 0.025 in THK, 301 Stainless Steel Band
ISOSTATIC™ Oilube® 402049 Round Bore Flange Bearing, 1/2 in Dia Bore, 5/8 in OD, 1 in W, 7/8 in Dia Flange
ISOSTATIC™ Oilube® 402049 Round Bore Flange Bearing, 1/2 in Dia Bore, 5/8 in OD, 1 in W, 7/8 in Dia Flange
OCCUPANCY SENSOR SWITCH-JWH501311>
3/8" X 3/8" USS SOCKET SET SCREW-NBS7190380038BP >
IKO IRB1216 Inch Series Inner Ring, 3/4 in ID x 1 in OD, 25.78 mm OAW, For Use With BA1616Z/BHA1616Z and YB1616 Shell Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. These rings are designed to provide a durable surface for shell-type needle roller bearings with non-machined raceways in-type IRB series shaft diameters range from 5/16 to 2-1/2 in.

