CM® M358P Super Strong Anchor Shackle, 35 ton Load, 2 in, 2-1/4 in Dia Round Pin, Orange Powder Coated
CM® super strong shackles are carbon type shackles with strength ratings that are 17 to 50% stronger than comparable sized carbon shackles. As a result, these shackles are designed with a 6:1 design factor. Anchor shackles can be side loaded or used for multiple connections.
-
BrandCM®
-
Manufacturer Part NumberM358P
-
CountryUSA
-
Load Capacity35 ton
-
FinishOrange Powder Coated
-
TypeSuper Strong
-
Inner Length7.44 in
-
Inner Width5-1/2 in
-
Size2 in
-
Opening Size3.28 in
-
Body MaterialMicro Alloy Steel
-
Eye Outer Size4.51 in
-
Pin Diameter2-1/4 in
-
Pin MaterialMicro Alloy Steel
-
Pin TypeRound
- Manufactured from technically advanced micro alloy steel with optimal hardness for strength and ductility
- Shackles show major deformation before failure
- Working load limit and traceability codes shown as permanent markings on body
- All shackles have alloy quenched and tempered pins
- Shackles meet dimensional requirements and exceed performance requirements of RR-C-271
- Round pin shackles have 5:1 design factor
-
UNSPSC24101641
-
Standards/ApprovalsASTM Certified|SAE J429|ASME B30.26|EN 13889|ANSI B18
-
Catalog
Recently Viewed
CM® super strong shackles are carbon type shackles with strength ratings that are 17 to 50% stronger than comparable sized carbon shackles. As a result, these shackles are designed with a 6:1 design factor. Anchor shackles can be side loaded or used for multiple connections.
MORSE® 43826 1901 Extra Long Length Non-Center Cutting Single End End Mill, 1/4 in Dia Cutter, 1-3/4 in Length of Cut, 4 Flutes, 3/8 in Dia Shank, 3-9/16 in OAL, Bright
MORSE® 43826 1901 Extra Long Length Non-Center Cutting Single End End Mill, 1/4 in Dia Cutter, 1-3/4 in Length of Cut, 4 Flutes, 3/8 in Dia Shank, 3-9/16 in OAL, Bright
MORSE® 57914 5943 Center Cutting Regular Length Single End End Mill, 7/32 in Dia Cutter, 5/8 in Length of Cut, 4 Flutes, 1/4 in Dia Shank, 2-1/2 in OAL, Bright
MORSE® 57914 5943 Center Cutting Regular Length Single End End Mill, 7/32 in Dia Cutter, 5/8 in Length of Cut, 4 Flutes, 1/4 in Dia Shank, 2-1/2 in OAL, Bright
RIDGID® 40100 Model 25A Bench Yoke Vise, Hardened Alloy Steel Jaw
MORSE® 44588 4582 Center Cutting Double End Regular Length End Mill, 3/8 in Dia Cutter, 3/4 in Length of Cut, 4 Flutes, 3/8 in Dia Shank, 3-1/2 in OAL, Bright
MORSE® 44588 4582 Center Cutting Double End Regular Length End Mill, 3/8 in Dia Cutter, 3/4 in Length of Cut, 4 Flutes, 3/8 in Dia Shank, 3-1/2 in OAL, Bright
RIDGID® 40090 Model 23A Bench Yoke Vise, Hardened Alloy Steel Jaw
