5-TON 5"-10.6" I-BEAM CLAMPS JET252750
JET JBC series features a more robust construction for increased durability and longer life in demanding industrial environments. The JBC series beam clamps come in capacities from 1 ton to 5 tons and can accommodate a beam up to 10 in wide. Each JET beam clamp jaw is designed to distribute the load away from the beam flange and adjusts easily for a wide range of standard H or I beams.
-
BrandJET®
-
UPC662755102783
-
Manufacturer Part NumberJT9-252750
-
CountryUSA
-
Load Capacity5 ton
-
SeriesJBC
- Durability
- Robust construction for increased durability and longer life in demanding industrial environments
- Welded, enclosed pockets provide greater stability and durability where the beam clamp attaches to the beam/structure
- Larger, thicker diameter pins for increased durability and life
- Welded all steel frame and powder coat finish provide maximum durability and protection
- Clamp jaw is designed to distribute the load away from the beam flange edge increasing safety
- Used for quick mounting of a hoist or for lifting a broad range of beams up to 10-5/8 in wide for increased versatility
- 5 - 10-5/8 in W beam flange
| Competitor Name | Competitor Part Number |
|---|---|
| MSC | 82341843 |
| MSC | 82341843 |
-
Alternative Part Number252750
-
UNSPSC24101600
-
Standards/ApprovalsANSI/ASME B30.17/B30.20
-
Specification Sheet
-
Owners/User Manual
Recently Viewed
JET JBC series features a more robust construction for increased durability and longer life in demanding industrial environments. The JBC series beam clamps come in capacities from 1 ton to 5 tons and can accommodate a beam up to 10 in wide. Each JET beam clamp jaw is designed to distribute the load away from the beam flange and adjusts easily for a wide range of standard H or I beams.
_100x100.jpg)
32-WATT WW MED CFL BULB (150-W EQ)-JWH509845>
TAPERED 1-1/16" X 1-1/4" . USED FOR REMOVING BURRS AND SMOOTHING DIMPLED OR DENTED AREAS IN PIPE-JWH326941 >
Dichtomatik N70435 O-Ring, 435 Dash Number, 5.725 in ID x 6.275 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Stanley Proto J4-HDL C-Clamp Extra Heavy-Duty 0-4-5/8-Inch-PROJ4HDL
Browning® 1296573 T65L Automatic Torque Limiter, 1-7/16 in Finished Bore, 6-1/2 in OD, 4800 in-lb (1-Spring)/8800 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
