LPS Chemical 11-OZ RED & REDI SPRAY RED GREASE LPS 05816
LPS® 05816 Multi-Purpose Grease, 16 oz Aerosol Can, Gas, Red, 22 to 450 deg F
-
BrandLPS®
-
UPC078827058160
-
Manufacturer Part Number05816
-
CountryUSA|Canada
-
Temperature Range22 to 450 deg F
-
Flash Point455 deg F
-
FormGas
-
ColorRed
-
TypeMulti-Purpose
-
GradeNLGI 2
-
CompositionPetroleum Oil, Petroleum Gases, Liquefied, 2-Methylpentane, 2,3-Dimethylbutane
-
VOC Content0.65
-
Viscosity3100 to 4000 cPs
-
Container Size16 oz
-
Container TypeAerosol Can
-
Base TypeAluminum Complex
-
Specific Gravity0.77 to 0.8
-
Odor/ScentSolvent
- Delivers excellent lubrication
- Prevents rust, corrosion and oxidation
- Easy visual inspection
- Remains effective at extremely high temperatures
- Penetrates quickly, resists shock
- Reduces friction and vibration
- No chlorinated solvents
- 550 deg F drop point
| Competitor Name | Cross-Reference Number |
|---|---|
| Grainger | 5YH77 |
-
UNSPSC15121902
-
Standards/ApprovalsOSHA 29 CFR 1910.1200
-
SDS
Recently Viewed
LPS® 05816 Multi-Purpose Grease, 16 oz Aerosol Can, Gas, Red, 22 to 450 deg F
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
5/8" STAINLESS STEEL SOLID SHAFT COLLAR
The LKN Series are fuse links designed for Littelfuse RLN series renewable fuses. Traditionally, Class H fuses were used to provide low cost protection of general purpose feeder and branch circuits where available short-circuit currents did not exceed 10,000 amperes. However, generally increased levels of available fault current and the distinct possibility that renewable fuses may be improperly renewed, rendering them unsafe, have all but eliminated the use of these fuses in new applications. In addition, escalating labour costs and increasing automation, which makes downtime very expensive, have greatly reduced or eliminated the cost savings attributed to renewable fuses.
Vortec Pro® 36012 Wide Face Wheel Brush With Nut, 4 in Dia Brush, 0.014 in Dia Standard/Twist Knot Filament/Wire, 5/8-11 Arbor Hole
Vortec Pro® 36012 Wide Face Wheel Brush With Nut, 4 in Dia Brush, 0.014 in Dia Standard/Twist Knot Filament/Wire, 5/8-11 Arbor Hole
Square D™ 8910DPA53V02 8910DPA Electro-Mechanical 3-Phase Electromechanical Type Dpa Definite Purpose Contactor, 110/120 V AC V Coil, 50 A, 3NO Contact, 3 Poles
8910DP definite purpose magnetic contactors are designed for heating, air conditioning and refrigeration applications. This line of definite purpose contactors has current ratings up to 120 amperes resistive and 50 HP at 600 VAC. This three pole definite purpose contactor has a full load rating of 50 ampere and a resistive rating of 65 amperes. It also has a 3 HP at 115 VAC single phase, 10 HP at 230 VAC single phase and 15 HP at 230 VAC three phase, 30 HP at 460 VAC three phase and 30 HP at 575 VAC three phase. The nonreplaceable coil is available with a variety of coil voltages. This device has a 110/120 VAC 50/60 Hz coil. The contactor has straight through wiring. Contactor is 4.06 inches by 2.56 inches and 3.67 tall. These contactors are UL component recognized and CSA certified.
