Crosby® 1032796 HG-228 1 X 6 JJ Turnbuckle, Jaw/Jaw, 1 in Thread, 10000 lb Working, 6 in Take Up, 21.18 in L Close, Steel
Crosby® 1032796 HG-228 Turnbuckle, Jaw/Jaw, 1 in Thread, 10000 lb Working, 6 in Take Up, 21.18 in L Close, Steel
-
BrandCrosby®
-
Manufacturer Part Number1032796
-
CountryUSA
-
FinishHot Dipped Galvanized
-
Thread Diameter1 in
-
MaterialSteel
-
Closed Length21.18 in
-
SeriesHG-228
-
Working Load10000 lb
-
End/EndJaw/Jaw
-
Take Up6 in
- End fittings are quenched and tempered or normalized, bodies heat treated by normalizing
- Forged jaw ends are fitted with bolts and nuts for 1/4 in through 5/8 in and pins and cotters on 3/4 in through 2-3/4 in sizes
- Modified UNJ thread on end fittings for improved fatigue properties
- Body has UNC threads
- Importantly, these turnbuckles meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26
-
UNSPSC31162405
-
Standards/ApprovalsFederal Spec FF-T-791b, Type 1, Form 1, Class 7|ASTM F-1145|ASME B30.26
-
Catalog
Recently Viewed
Crosby® 1032796 HG-228 1 X 6 JJ Turnbuckle, Jaw/Jaw, 1 in Thread, 10000 lb Working, 6 in Take Up, 21.18 in L Close, Steel
Crosby® 1032796 HG-228 Turnbuckle, Jaw/Jaw, 1 in Thread, 10000 lb Working, 6 in Take Up, 21.18 in L Close, Steel
Weiler® 08155 ST-8 Heavy-Duty Wheel Brush, 8 in Dia Brush, 5/8 in W Face, 0.023 in Dia Filament/Wire Standard/Twist Knot Filament/Wire, 5/8 in Arbor Hole
Weiler® 08155 ST-8 Heavy-Duty Wheel Brush, 8 in Dia Brush, 5/8 in W Face, 0.023 in Dia Filament/Wire Standard/Twist Knot Filament/Wire, 5/8 in Arbor Hole
Proto® J226G Needle Nose Plier With Side Cutter and Wire Stripper, Diamond Serrated Steel Jaw, 1-7/8 in L x 11/16 in W Jaw, 6-5/8 in OAL, 3/8 in W Tip
2" -FEMALE PIPE THREAD BLACK STREET TEE-JPW2BSTT >
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
he Crosby G-429 1/2" refers to the 1/2-inch Galvanized Fist Grip® Wire Rope Clip manufactured by Kito Crosby. Unlike traditional U-bolt style clips, this heavy-duty dual-saddle clamp features integral bolts and nuts that allow for rapid installation and eliminate the risk of installing the clip upside down
