Klein Tools CONDUIT FTG/REAMING SCREWDRIVERS KLE 85191
The Klein Tools Conduit-Fitting and Reaming Screwdriver can ream and smooth 1/2'' (13 mm), 3/4'' (19 mm), and 1'' (25 mm) thin-wall conduit. It features a hooded-blade design that keeps the screwdriver tip from slipping out of screws, which is especially handy when tightening hard-to-reach conduit fittings. This screwdriver has a longer Cushion-Grip™ handle for even more comfort and torque while reaming.
-
BrandKlein®
-
UPC092644851919
-
Manufacturer Part Number85191
-
CountryUSA|Canada
-
Point Size5/16 in
-
MaterialSteel
-
Measurement SystemImperial
-
ColorBlack/Yellow
-
TypeConduit Fitting and Reaming
-
Handle MaterialPlastic
-
Handle TypeCushion Grip
-
Shank Length2-1/2 in
-
Shank MaterialSteel
-
Overall Length7-1/2 in
- Reamer's hooded-blade design keeps tip from slipping out of screws, especially when tightening hard-to-reach conduit fittings, thicker hood is designed for rugged use
- Reams and smooths 1/2 in (13 mm), 3/4 in (19 mm), and 1 in (25 mm) thin-wall conduit ends to protect wire and permit correct installation of fittings
- Reams both the inside and outside of the conduit at the same time
- Replaceable reaming blade is now held in place with a 1/16 in hex socket set screw
- Thinner screwdriver blade allows easier access to screw heads
| Competitor Name | Cross-Reference Number |
|---|---|
| Grainger | 5LL70 |
| MSC | 01763929 |
-
Alternative Part Number8522431
-
UNSPSC27111701
-
IDEA Index ID8522431
-
Package DescriptionEACH
-
Standards/ApprovalsPROP65: Cancer and reproductive harm - See www.P65Warnings.ca.gov for more information
-
Catalog
Recently Viewed
The Klein Tools Conduit-Fitting and Reaming Screwdriver can ream and smooth 1/2'' (13 mm), 3/4'' (19 mm), and 1'' (25 mm) thin-wall conduit. It features a hooded-blade design that keeps the screwdriver tip from slipping out of screws, which is especially handy when tightening hard-to-reach conduit fittings. This screwdriver has a longer Cushion-Grip™ handle for even more comfort and torque while reaming.
MORSE® 17177 2332 Type J Heavy Duty Jobber Length Jobber Drill, D Drill - Letter, 0.246 in Drill - Decimal Inch, 135 deg Point, Cobalt
1-GAL AIR COMPRESSOR OIL-CACP08909A1 >
LPS® 05816 Multi-Purpose Grease, 16 oz Aerosol Can, Gas, Red, 22 to 450 deg F
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
5/8" STAINLESS STEEL SOLID SHAFT COLLAR
