Dichtomatik N70457 O-Ring, 457 Dash Number, 13.975 in ID x 14.525 in OD, Nitrile Rubber, 70 Shore A Durometer, Import, Custom 457
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70457
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter13.975 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter14.525 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
V-BELTOUTSIDE CIRCUMFERENCE 60."-JAS3V600 >
WATTS® 0002220 1L Series Self-Closing Temperature and Pressure Relief Valve, 1/2 in Nominal, MNPT x FNPT End Style, 125 psi Pressure, 210 deg F, Bronze Body
This 1/2 inch temperature and pressure relief valve is used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 15,000 BTU/hr. It features a bronze body with NPT threaded male inlet and NPT threaded female outlet connections, 2 inch short thermostat with special thermo-bonded coating and test lever. It is CSA listed. Temperature relief at 210 degrees F (99 degree C), pressure relief range is 75 to 150 psi. The standard pressure settings is 125 psi.
Dodge® 023006 111 Type E-Xtra Pillow Block Roller Bearing Unit, 1-11/16 in Dia Bore, 6.13 to 6.38 in L Bolt Center-to-Center, 2.13 in Base to Bore Centerline, 7.88 in OAL x 4-1/4 in OAH
Dodge® 023006 111 Type E-Xtra Pillow Block Roller Bearing Unit, 1-11/16 in Dia Bore, 6.13 to 6.38 in L Bolt Center-to-Center, 2.13 in Base to Bore Centerline, 7.88 in OAL x 4-1/4 in OAH
Moldex® 2400N95 Disposable Particulate Respirator With Exhale Valve, M/L, Resists: Heat, Flame, Nuisance Organic Vapors and Non-Oil Based Particulates
Morse® Real McCoy® TA34 Hole Saw, 2-1/8 in Dia, 1-1/2 in D Cutting, M3 HSS Cutting Edge
