Dichtomatik 75102339 O-Ring, 445 Dash Number, 7.975 in ID x 8.525 in OD, FKM, 75 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part Number75102339
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialFKM
-
ColorBlack
-
Inside Diameter7.975 in
-
Domestic/ImportImport
-
Durometer75 Shore A
-
Outside Diameter8.525 in
- Good chemical resistance to mineral oils and greases, synthetic oils and greases, motor, transmission and ATF oils up to 150 deg C
- Very good weathering, ozone and aging resistance
- Very low gas permeability
-
UNSPSC31401503
-
Standards/ApprovalsASTM D1418|AS 568B|BS 1806|JIS 2401
-
Alternative Part NumberV75445
-
Instruction/Installation Manual
-
Specification Sheet
-
Catalog
Recently Viewed
Dichtomatik 75102339 O-Ring, 445 Dash Number, 7.975 in ID x 8.525 in OD, FKM, 75 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Dodge® 128648 205 Normal Duty Ball Insert Bearing, 1 in Dia Bore, 2.0472 in OD, 1.44 in W, 3146 lb Dynamic/1769 lb Static Load
Dodge® 128648 205 Normal Duty Ball Insert Bearing, 1 in Dia Bore, 2.0472 in OD, 1.44 in W, 3146 lb Dynamic/1769 lb Static Load
Sealmaster® 700398 SEHB Non-Expansion Standard-Duty Hanger Ball Bearing Unit, 1-7/16 in Dia Bore, 3-3/4 in OD, 1-15/16 in W, Cast Iron Bearing, Set Screw Collar Locking
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
Leviton® S701-GY Standard Size Wall Plate, 2 Gangs, 4.56 in W x 4.5 in H, Steel, Gray
Leviton® S701-GY Standard Size Wall Plate, 2 Gangs, 4.56 in W x 4.5 in H, Steel, Gray
Browning® 767409 VPLS 200 Normal Duty Low Base Pillow Block Ball Bearing Unit, 1-5/8 in Dia Bore, 5-13/64 to 6-7/64 in L Bolt Center-to-Center, 2-1/16 in Base to Bore Centerline, 7-3/8 in OAL x 4-3/16 in OAH
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric or BOA concentric locking collar. The contact seal with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction.
Sealmaster® 700367 SCHB Non-Expansion Standard-Duty Hanger Ball Bearing Unit With Seal Flinger, 2 in Dia Bore, 4.38 in OD, 2.03 in W, Cast Iron Bearing, Set Screw Collar Locking
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
