Dichtomatik N70366 O-Ring, 366 Dash Number, 7.225 in ID x 7.645 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70366
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter7.225 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter7.645 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
Dichtomatik N70366 O-Ring, 366 Dash Number, 7.225 in ID x 7.645 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
BBI 221097 Shoulder Screw, Round Socket Head, ASTM A574 Alloy Steel, 3/8 in Dia x 4 in L Shoulder, 5/16-18
BBI 221097 Shoulder Screw, Round Socket Head, ASTM A574 Alloy Steel, 3/8 in Dia x 4 in L Shoulder, 5/16-18
Sharkbite® U855W100 Tubing, 3/8 in Nominal, 0.35 in ID x 1/2 in OD x 100 ft Coil L x 0.07 in THK Wall, White, PEX, Domestic
SharkBite® PEX Pipe is a cross-linked polyethylene pipe used for potable water application. The pipe is printed with a SharkBite® imprint pattern that provides a visual aid to determine if the pipe has been inserted all the way into the SharkBite® Push-To-Connect (PTC) fitting. This feature only works if the pipe is cut between the SharkBite® imprint pattern.
Sintered steel bushing on which the center member and friction facings rides are coated with a dry film lubricant; therefore, no oil is present to contaminate friction facings and reduce torque capacity. The bushing "free floats" on the hub. Morse® offers a wide selection of bushing widths in all torque limiter sizes, permitting close matching of center member and bushing width to minimize bearing pressure and promote longer bushing life.
MORSE® 22174 1655 Chucking Reamer, 7/32 in Dia x 5 in OAL, 0.2075 in Dia Straight Shank, Straight Flute
MORSE® 22174 1655 Chucking Reamer, 7/32 in Dia x 5 in OAL, 0.2075 in Dia Straight Shank, Straight Flute
BBI 451172 Partially Threaded Cap Screw, 5/8-11, 13 in L Under Head, 8 Grade, Alloy Steel, Plain
BBI 451172 Partially Threaded Cap Screw, 5/8-11, 13 in L Under Head, 8 Grade, Alloy Steel, Plain
