Dichtomatik N70360 O-Ring, 360 Dash Number, 5.85 in ID x 6.27 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70360
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter5.85 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter6.27 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
-
Catalog
-
Instruction/Installation Manual
-
Specification Sheet
Recently Viewed
Dichtomatik N70360 O-Ring, 360 Dash Number, 5.85 in ID x 6.27 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
EZ-FLO® 36215 Faucet Slip-Joint washer, 1-1/2 in Nominal
The Eastman Slip-Joint Washer is constructed of a high-impact polyethylene plastic for a long-lasting durability. The white washer measures 1-1/2 inch. Designed for use in tubular drain applications, the washer works in conjunction with a slip-joint nut (not included) to seal the connection between PVC pipes to prevent leakage. Sold and priced 100 per order.
11" 50# UV BLACK 100 PER BAG-CTE1150UV100 >
BBI 451195 Partially Threaded Cap Screw, 1-14, 8-1/2 in L Under Head, 8 Grade, Alloy Steel, Plain
BBI 451195 Partially Threaded Cap Screw, 1-14, 8-1/2 in L Under Head, 8 Grade, Alloy Steel, Plain
Milwaukee® 48-44-0122 Shear Blade Set, For Use With 6805 Metal Cutting Shear, 16/18 ga Capacity
This 16 gauge shear blade set includes both top and bottom blade to renew the cutting sharpness of your Milwaukee model 6805 metal cutting shear. Use feeler gauge 49-11-0080 to set the gap appropriately per the tool instruction manual.
Channellock® 356 Non-Insulated Standard End Cutting Plier, 0.056 to 0.091 in Piano Wire Cutting, 0.35 in, 6-1/4 in OAL, Plastic Handle
CHANNELLOCK® High Leverage End Cutting Pliers feature Xtreme Leverage Technology (XLT™) which makes cutting easier than ever. By positioning the rivet closer to the cutting edge, considerably less force is required to cut than other high leverage designs. State-of-the-art laser heat treating offers a strong and consistent pattern across the cutting edge for increased strength and longevity. These pliers also offer a slimmer, lighter, and better-balanced design for maximum performance and accessibility. CHANNELLOCK® End Cutting Pliers are made in USA and forged from high carbon U.S. steel that is specially coated for ultimate rust prevention.
