Dichtomatik 75102163 O-Ring, 241 Dash Number, 3.859 in ID x 4.137 in OD, FKM, 75 Shore A Durometer, Import, Custom 241-VITON
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part Number75102163
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialFKM
-
ColorBlack
-
Inside Diameter3.859 in
-
Domestic/ImportImport
-
Durometer75 Shore A
-
Outside Diameter4.137 in
- Good chemical resistance to mineral oils and greases, synthetic oils and greases, motor, transmission and ATF oils up to 150 deg C
- Very good weathering, ozone and aging resistance
- Very low gas permeability
-
UNSPSC31401503
-
Standards/ApprovalsASTM D1418|AS 568B|BS 1806|JIS 2401
-
Alternative Part NumberV75241
-
Specification Sheet
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Dichtomatik 75102163 O-Ring, 241 Dash Number, 3.859 in ID x 4.137 in OD, FKM, 75 Shore A Durometer, Import, Custom 241-VITON
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
18" WHITE BOUFFANT CAPS--BOX OF 1000-CPPBC18 >
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric, or BOA concentric locking collar. The contact seal, with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction. Depending on your preference, these bearings are available in inch and metric bore with a wide variety of cast iron, stamped steel or rubber mount housings or specific industry solutions as illustrated on the pages to follow.
MORSE® 22588 1680 Taper Pin Reamer, #1 Taper Pin, 0.1447 in Dia Small End, Straight Flute, Straight Shank
ILSCO® ClearChoice® 23210-B2 Heavy Wall Flame Retardant Shrink-On Tubing Cap, 600 V AC, 2.05 in ID Expanded, 3/4 in ID Recovered, 3:1 Shrink Ratio
ILSCO® ClearChoice® 23210-B2 Heavy Wall Flame Retardant Shrink-On Tubing Cap, 600 VAC, 2.05 in ID Expanded, 3/4 in ID Recovered, 3:1 Shrink Ratio
Gates® Power Transmission Hi-Power® B83 Heavy Duty V-Belt, B Section, 21/32 in W Top, 86 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
