Dichtomatik N70218 O-Ring, 218 Dash Number, 1.234 in ID x 1.512 in OD, Nitrile Rubber, 70 Shore A Durometer, Import, Custom 218
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70218
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter1.234 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter1.512 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
14-MM-PITCHX2100-MM TIMING BELT-JAS210014M68 >
BRUSH RESEARCH GBD-31/2180-SC Heavy Duty Flexible Cylinder Hone, 3-1/2 in Dia Bore, 5 in L Abrasive, 13-1/2 in OAL, 180 Grit
The BRM Flex- Hone® Tool is a resilient, flexible honing tool with a soft cutting action. It's unique construction allows the abrasive globules or "stones" to float, assuring the tool will be self-centering, self-aligning to the bore and self-compensating for wear. The tool is available in a variety of different grits and sizes ranging from 4 mm to 36 in. Whether your need is cross hole deburring, surface finishing or edge blending there is a Flex- Hone® Tool designed for you. A non-directional or crosshatched pattern is created on the surface that contains valuable valleys between the plateaus for oil retention. Finer grits can assist with achieving single RA finishes. In Automotive, Hydraulic, Pneumatic or Industrial applications, the Flex- Hone® Tool will provide a superior surface finish bringing increased product performance, longer product life and less product reject.
Jacobs® 7316DN Spindle Drill Chuck Arbor, #3 MT x #4 JT Mount Taper, Morse Taper Shank
Jacobs® 7316DN Spindle Drill Chuck Arbor, #3 MT x #4 JT Mount Taper, Morse Taper Shank
1-1/4" -ID 3-BOLT FLANGE UNIT-MBUVF3E120M >
1-1/4" -ID NU-LOC ER-STYLE INSERT-FYHERC20620 >
