Dichtomatik N70204 O-Ring, 204 Dash Number, 0.359 in ID x 0.637 in OD, Nitrile Rubber, 70 Shore A Durometer, Import, Custom 204
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70204
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter0.359 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter0.637 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
AMBER REPLACEMENT LENS/ASTRO 3000-SSSS537>
Browning® 3779949 VP Series Type 2 Variable Pitch Sheave, 1-3/8 in Finished Bore, 6.55 in OD, 1 Groove, 4.9 to 5.9 in (A/4L)/5.2 to 6.4 in (B/5L/5V) Dia Pitch, 7/8 to 1-1/4 in W Face
The principle of a variable pitch sheave is that the threaded angular faced discs forming the V-shaped groove in which the belt rides are movable. VP sheaves consist of a male with a threaded barrel, and a female with a threaded bore. The male section with threaded barrel has flat surfaces at 180 deg increments that allow a flat surface for the setscrew to mate with. When the discs are moved toward each other, the belt rides higher in the groove and the pitch diameter of the sheave is larger which increases the driven speed. When the discs are moved away from each other, the belt rides lower and the pitch diameter is smaller decreasing the driven speed. The common term for this speed adjustment is called number of turns open from closed position.
CLEAR BLACK FRAME SAFETY GLASSES-UVXUVS092>
1-1/4" -MALE PIPE THREADX3/4" FEMALE PIPE THREAD BLACK BUSHING-FIT11/4X3/4BB >
Milwaukee® 49-16-2732 Cordless Rust-Resistant Professional Saw Chain, For Use With Narrow Kerf Bars, 3/8 in Low Profile Pitch, Steel
The MILWAUKEE® 6" 3/8" Low Profile Pitch, .043" Gauge Saw Chain features a full house chain that delivers smooth pruning and clean finishes. The chain is designed for controlled, low-vibration cuts. The narrow kerf, Low Profile cutters offer more cuts per charge versus standard kerf to help maximize battery efficiency. This chain is recommended for use with the M12 FUEL™ HATCHET™ 6” Pruning Saw (2527-20) and 6" 3/8" Low Profile Pitch, .043" Gauge Guide Bar (49-16-2733) and fits saws & narrow kerf bars of the same pitch, gauge, length, and drive links.
