Dichtomatik N70152 O-Ring, 152 Dash Number, 3.237 in ID x 3.443 in OD, Nitrile Rubber, 70 Shore A Durometer, Import, Custom 152t
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70152
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter3.237 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter3.443 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Irwin® 04 7LW® 1-Handed Lever Locking Wrench, 3/4 in Nominal, 1-3/16 in L x 3/8 in W x 1/2 in THK Alloy Steel V-Shape Jaw, 7 in OAL, Yes
IRWIN Tools VISE-GRIP Locking Wrench with Wire Cutter (4US). Curved jaw delivers maximum gripping power and won't slip or strip on any style of nut or bolt. Built-in wire cutter means you don't have to switch tools. Constructed of high-grade heat-treated alloy steel for maximum toughness and durability. Guarded trigger gives you a quick release while helping prevent accidental release. Adjust pressure and work fit with turn screw that stays adjusted for repetitive use..
3/4" X 12" RED HD RECT DIE SPRINGS-LANSHDR7501200 >
1-3/16"-ID 1210-STYLE TAPER-LOCK BUSHING - IDC12101.3/16 >
Crosby® 1032554 HG-228-1/2 x 6 Turnbuckle, Jaw/Jaw, 1/2 in Thread, 2200 lb Working, 6 in Take Up, 14.14 in L Close, Steel
Crosby® 1032554 HG-228 Turnbuckle, Jaw/Jaw, 1/2 in Thread, 2200 lb Working, 6 in Take Up, 14.14 in L Close, Steel
MINI HACKSAW BLADE-JWH355623 >
