Dichtomatik N70137 O-Ring, 137 Dash Number, 2.05 in ID x 2.256 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70137
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter2.05 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter2.256 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
Dichtomatik N70137 O-Ring, 137 Dash Number, 2.05 in ID x 2.256 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
50-LBS #6013-5/32" WELDING RODS E6013 mild steel "General Purpose" is an all-position, general-purpose rod with medium to shallow penetration. Medium to heavy slag is easily removed. Excellent for poorly fitted joints. Smaller sizes of rod are well suited to low heat on thin metals. Use on all types of mild steel where ease of operation and good appearance is required. Great for light gauge metal, sheet metal, duct work, etc.
BBI 451030 Partially Threaded Cap Screw, 1-1/4-7, 4 in L Under Head, 8 Grade, Alloy Steel, Plain
BBI 451030 Partially Threaded Cap Screw, 1-1/4-7, 4 in L Under Head, 8 Grade, Alloy Steel, Plain
BBI 440492 Partially Threaded Hex Bolt, 5/8-11, 2-1/4 in L Under Head, L9 Grade, Alloy Steel, Zinc Yellow CR+3
BBI 440492 Partially Threaded Hex Bolt, 5/8-11, 2-1/4 in L Under Head, L9 Grade, Alloy Steel, Zinc Yellow CR+3
Crosby® 1043677 G-291 Eye Bolt With Regular Nut, 3/4 in, 15 in L Shank, Forged Steel, Hot Dipped Galvanized
Crosby® 1043677 G-291 Eye Bolt With Regular Nut, 3/4 in, 15 in L Shank, Forged Steel, Hot Dipped Galvanized
5/8" X 18" L CONCRETE ANCHOR BOLT-NBS9290621800 >
