Dichtomatik S70116 O-Ring, 116 Dash Number, 0.737 in ID x 0.943 in OD, Silicone Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberS70116
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialSilicone Rubber
-
ColorRed
-
Inside Diameter0.737 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter0.943 in
- Good chemical stability in water (up to 100 deg C), aliphatic engine and transmission oils, animal and plant based oils and greases
- Not resistant to fuels, aromatic mineral oils, water vapor (short periods up to a maximum of 120 deg C are possible), silicone oils and greases, along with acids and alkaline compounds
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|ISD Certified|NFPA Listed|PTDA Certified
-
Instruction/Installation Manual
-
Catalog
-
Specification Sheet
Recently Viewed
Dichtomatik S70116 O-Ring, 116 Dash Number, 0.737 in ID x 0.943 in OD, Silicone Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
OIL SEALS-1.632" X 2.191" X .250"-IMS13500>
Dichtomatik N70364 O-Ring, 364 Dash Number, 6.725 in ID x 7.145 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
40-B-38-F-3/4 38 Tooth Sprockets For #40
38 TOOTH SPROCKETS FOR #40 CHAIN-IDC40B38F3/4 >
The United Abrasives/SAIT Type 27 Saitech Ultimate Performanceâ„¢ wheels are made to go on an angle grinder. High performance, ceramic aluminum oxide grain, is designed to outlast standard aluminum oxide wheels. Hard bond for long life grinding with fast stock removal. Very uniform, high density grain structure for long life and cooler cut. United Abrasives/SAIT wheels are reinforced with the highest quality fiberglass for maximum safety and performance. Proudly manufactured in the USA.
