Dichtomatik S70111 O-Ring, 111 Dash Number, 0.424 in ID x 0.63 in OD, Silicone Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberS70111
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialSilicone Rubber
-
ColorRed
-
Inside Diameter0.424 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter0.63 in
- Good chemical stability in water (up to 100 deg C), aliphatic engine and transmission oils, animal and plant based oils and greases
- Not resistant to fuels, aromatic mineral oils, water vapor (short periods up to a maximum of 120 deg C are possible), silicone oils and greases, along with acids and alkaline compounds
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|ISD Certified|NFPA Listed|PTDA Certified
-
Instruction/Installation Manual
-
Catalog
-
Specification Sheet
Recently Viewed
Dichtomatik S70111 O-Ring, 111 Dash Number, 0.424 in ID x 0.63 in OD, Silicone Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Milwaukee® 2447-20 Flat Bare Tool Crown Stapler, 3/8 in Crown, For Fastener Type: Staples, 7-1/4 in OAL, Li-Ion Battery
The Milwaukee M12™ 3/8 in. crown stapler delivers a true hand tool replacement. The 2447 is designed to drive a range of 3/8 in. flat crown staples (1/4 in. – 9/16 in.) through an array of materials and substrates. At just 3.0 lbs. and 7.5 in. long the compact design allows for great access into tight spaces and convenient tool belt portability. An easy to squeeze trigger design significantly reduces fatigue associated with traditional hand staplers. Integrated sequential and contact actuation trigger design provides increased productivity and seamless changing between firing modes. The 2447 is compatible with all Milwaukee M12™ batteries, and carries Milwaukee's 5-year limited power tool warranty.
The DCB206 DEWALT 20V MAX 6.0Ah XR Battery provides immediate feedback on state of charge with the 3-LED Fuel Gauge System and has a lightweight design for easy transporting of DEWALT 20V MAX battery.
Sealmaster 1-3/4"-ID 4-BOLT SPH FLANGE UNITS BRW SFC-1000-NE X 1-3/4
Sealmaster® USRB performance mounted spherical roller bearings feature black oxide treated bearing steel races with optimized bearing geometry for load capacity, misalignment and speed capabilities. The USRB is available in both setscrew locking and adapter mounting system. The felt seal with flinger provides a good balance between contaminant entry, grease retention and friction. Depending on application requirements, these bearings are available in a wide variety of bore sizes, housing styles and sealing options.
Koyo IR-2424 Inch Series Regular Width Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 1.515 in OAW, For Use With Inch Series Drawn Cup Needle Roller Bearing, Steel
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Browning 3-7/16"-ID 4-BOLT TRB PILLOW BLOCK BRW PBE-920F X 3-7/16
Browning® E920 series mounted tapered roller bearings feature durable 1-piece non-expansion housings with Type E mounting dimensions and limited misalignment. The E920 series contains setscrew locking collars for easy installation. It also contains a contact face riding seal in order to provide a good balance between contaminant entry, grease retention and friction. Depending on your application requirements, these bearings are available in a wide variety of bore sizes and housing configurations.
